Motorola DCH3000 Installation Manual Download | Manualshive

Page: 21 / 72

background image

3 INSTALLATION

11

•

Otherwise, use the baseband left and right audio out outputs.

3.

Locate the cabling diagram(s) that best match the subscriber’s configuration.

4.

Connect the audio and video cables in a manner matching that diagram.

5.

Determine if you are connecting to a data device (see

Data Device Connections

in

this section). For installation details, refer to the instructions included with the data
device.

6.

Connect the cable terminal to the coaxial cable wall outlet.

7.

Perform the operational check for the remote control.

8.

Optimize the high-definition settings. See

Optimizing the High-Definition Settings

in

this section.

«
...
19
20
21
22
23
...
»

Summary of Contents for DCH3000









































































Reviews:

No comments

Related manuals for DCH3000

Performance AV1

Brand: JBL Pages: 160

Brand: JBL Pages: 6

Brand: VDO Pages: 2

Brand: VDO Pages: 2

Brand: Xoro Pages: 44

Brand: Xomax Pages: 18

Brand: VDO Pages: 1

Brand: Yaesu Pages: 15

Brand: Yaesu Pages: 99

Brand: Yaesu Pages: 20

Brand: Yaesu Pages: 2

Brand: Yaesu Pages: 176

Brand: GRAUPNER Pages: 52

Brand: Ignition Pages: 9

Brand: Aiwa Pages: 33

Brand: Yaesu Pages: 77

Brand: Spotwave Pages: 2

Brand: Icom Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands