Motorola BR700 - EN Broadband Router User Manual Download

Page: 31 / 78

SECTION 2

INSTALLATION

2-18 SECTION

INSTALLATION

Static IP

If you are required to use a permanent IP address for connecting to
the Internet, then select

Static IP

. Your ISP informs you if this is the

connection to use.

From Connection Mode, select

Static IP

In the IP Address field, enter the

IP Address

supplied by your

ISP.

In the Subnet Mask field, enter the

Subnet Mask

supplied by

your ISP.

In the Default Gateway field, enter the values supplied by your
ISP.

In the Primary DNS field, enter the values supplied by your ISP. If
necessary, enter secondary or tertiary DNS values into the
Secondary or Third

DNS

fields.

Click

Apply

to save the setting, or, if you wish to start over, click

Cancel

PPTP

Point to Point Tunneling Protocol (PPTP) is a service commonly
found in Europe.

From Connection Mode, select

PPTP

In the PPP User Name field, enter the

PPP User Name

supplied

by your ISP.

In the PPP Password field, enter the

PPP Password

supplied by

your ISP.

In the PPTP Client IP field, enter the

PPTP Client IP

address

supplied by your ISP.

In the PPTP Server IP field, enter the

PPTP Server IP

address

supplied by your ISP.

Click

Apply

to save the setting, or, if you wish to start over, click

Cancel

Summary of Contents for BR700 - EN Broadband Router















































































Search results

Summary of Contents for BR700 - EN Broadband Router

Reviews:

Related manuals for BR700 - EN Broadband Router

Brands by name

Popular brands

Motorola BR700 - EN Broadband Router, User Manual

Search results

Summary of Contents for BR700 - EN Broadband Router

Reviews:

Related manuals for BR700 - EN Broadband Router

Brands by name

Popular brands