6A
6B
EN
EN
03. CONFIGURATION
03. CONFIGURATION
EXTENDED MENU 2
LED
LED OFF
LED ON
•
CODE
Programming Distance = OFF
Programming Distance = ON
•
CODE PED.
Photocells test = OFF
Photocells test = ON
•
IN.CMD.AP
Not used
•
L. CORT.
Not used
•
PGM. AUT.
Not used
•
T. MOT.
PUL=Open / Close | BL = STOP
PUL=Open | BL = Close
•
T. MOT. PED
Flashing simultaneously ON/OFF
•
T. PAUSA
Flashing simultaneously ON/OFF
EXTENDED MENU 1
EXTENDED MENU 2
With the pause time programmed, it is possible to trigger the “Follow Me” option.
With this option enabled, whenever the photocells detect a some user/object passing be-
tween them, the control board triggers the closing maneuver 5 seconds after the detection.
Activate (LED ON)/deactivate (LED OFF) function:
01. Activate the extended menu 1 (see ACCESSING EXTENDED MENU 1 on page 5B).
02. Press SEL button once, the CODE LED will begin to flash. Press the SEL button the
times necessary until the
PGM AUT PED starts to flash.
03. Press SET button once to enable / disable the function.
The
PGM AUTO LED ON indicates that the function is active and the LED OFF indicates
that the function is deativated.
With this function active, the control board triggers the flashing lightbulb output (CN4 4
and 5 connectors) 3 seconds before starting any opening or closing maneuver. The control
board is supplied by the manufacturer with the step-by-step operation mode disabled.
Activate (LED ON) / deactivate (LED OFF) function:
01. Activate the extended menu 1 (see ACCESSING EXTENDED MENU 1 on page 5B).
02. Press SEL button once, the CODE LED will begin to flash. Press the SEL button the
times necessary until the
LED CODE PED starts to flash.
03. Press SET button once to enable/disable the function. The CODE PED LED ON indica-
tes that the function is active and the
LED OFF indicates that the function is deativated.
• PGM. AUT. |
FOLLOW ME
• CODE PED. |
PRE-LIGHTBULB
• ACCESSING THE EXTENDED MENU 2
To access the options from Extended Menu 2, read the following instructions:
01. Activate the extended menu 1 (see ACCESSING EXTENDED MENU 1 on page 5B).
02. While T.MOT.PED and T.PAUSA LEDs blink alternately, return to continuously press the
SET button for 5 seconds until they blink simultaneously.
03. The control board provides 30 seconds to select functions form the extended menu 2
(using the
SEL and SET buttons), and after this time it returns to the main menu.
barrier will reverse the direction of operation until reaching the limit-switch.
Operation in Step-by-Step Mode (CODE LED OFF):
For every order sent by the transmitter / push button, the control board will behavior
in this way: open-stop-close-stop-open(…). The control board is supplied by the manu-
facturer with the step-by-step operation mode active.
To change the operating mode, follow these instructions:
01. Activate the extended menu 1 (see ACCESSING EXTENDED MENU 1 on page 5B).
02. Press SEL button once, the CODE LED will begin to flash.
03. Press the SET button once to change programming.
The
CODE LED will turn on / turn off permanently, signaling the success of operating
mode alteration.
Activating the distance transmitter programming function:
01. Activate the extended menu 2 (see ACCESSING EXTENDED MENU 2 on page 6B).
02. Press SEL button once, the CODE LED will begin to flash.
03. Press for 1 second the SET button and the CODE LED will light up permanently, in-
dicating the programming’s success.
Repeat the operation to restore the previous configuration.
To program a transmitter at distance, read the following instructions:
01. Press the a button from a configured transmitter for longer than 10 seconds wi-
thout releasing. The CODE LED will start to flash indicating that the control board is in
programming mode.
02. Press for 1 second the new transmitter button you want to program.
• CODE |
DISTANCE TRANSMITTER PROGRAMMING
