15.A
15.B
▷ Initial operating conditions
The MC7control board can work connected with one Sun / Rain / Wind wireless sensor.
▷ Centralization via radio through transmitter
The centralization of two or more control boards via radio allows simultaneous
movement of ascending or descending of several awnings.
The centralization is performed by entering the same codes (keys) from a transmitter to
all control boards at maximum distance of 20 meters from the transmitter point in, in
order to get the general or partial motion of more automations. For a satisfactory radio
centralization, you must choose carefully the location of installation.
The operating range is not only related with the technical characteristics of the device,
it may vary depending on the radioelectric conditions of the location.
▷ Programming buttons and indicator LEDs
SEL key:
selects the type of function to be memorized, the choice is indicated by the
flashing of the LED. Pressing the button more times, it is possible to position yourself in the
desired function. The flashing LED indicates that the selection is active, but the duration is
15 seconds. At the end of this period, the control board returns to its normal status.
SET button:
makes the choosen programming with the SEL button.
LED signaling
LED ON:
option saved
LED OFF:
option not saved.
Intermittent LED:
option selected.
▷ Main menu
CODE
(Programming the remote control to operate the awning and the wireless Wind
Sensor)
CODE LAMP
(Programming the remote control to operate a lamp)
T.MOT
(Programming the Working Time/ motor)
▷ Programming the remote control 1 or 2 keys and Wireless Sensor
The programming of the transmission codes of the remote control is performed as
following: press the
SEL
button and CODE LED will blink. At the same time, send the first
code (closing) selected with the desired remote control. The LED CODE will flash rapidly.
Send the second code (opening) to be memorized, the LED CODE will remain ON and
programmation is finished. If the second code is not sent within 10 seconds from the
first one, the unit exits the programming phase, leaving only a button on the remote
control to work step by step (open/stop/close).
▷ Programming sensor wireless (sun/wind/rain)
If you want to memorize a wireless sensor, follow these steps:
1º
Turn ON the power supply of the sensor;
2º
Open the memory of the control board MC7. For this step we have two options:
(option 1) - Open the control board as follows: use the SEL button to go to the LED
CODE. (option 2) - With the awning openned and lighting turned off, continually press
the remote’s opening channel memorized for more than 10 seconds until the light of
the awning flashes once;
After opening the control board’s memory, you have 10 seconds to send the sensor’s
order to the control board.
3º
(Sensor) Use the SEL button to go to the LED CODE (led starts to blink), immediately
press the SET button of the sensor so that it emits a rapid flashing of the LED
CODE until the light of the awning flashes once;
4º
With the SELbutton of the sensor, you must
now select the functions you want to leave
activated in the sensor the sun/wind/rain. Press
SELrepeatedly until the LED of the desired
function flashes. With the LED flashing, press
the SETbutton for more than 1 second until it is
fixed (LED turned on = active function).
To disable any function, repeat point 4 but press
the SET button at least 1 second and the LED goes
out, leaving the function disabled.
5º
To test the sensor you should follow the next instructions:
With the SELbutton position yourself on the flashing of the LED TEST. Press the SET
button for more than 1 second and the LED stays on.
TEST RAIN SENSOR
Place a wet finger over the sensor until the awning begins to close
(the awning will close during 5 seconds).
TEST WIND SENSOR
Rotate the propeller. The awning will close for 5 seconds.
TEST SUN SENSOR
Turn VR1clockwise (+) and the awning will open for 5 seconds.
Turn the VR1 counterclockwise (-) and the awning will close for 5 seconds.
In case the awning performs the indicated operations successfully, the sensor is
programmed and the test finished.
You must deactivate the LED TEST so that, in case of emergency, the awning
closes entirely. If the LED TEST stays on, the awning will only close for 5 seconds.
When the awning closes by sensor’s order, we can see what order is being sent,
checking which LED of the sensor is ON, on the board’s monitor.
For more information on how to adjust the wind speed, sensitivity and sensor’s
illuminance, read the manual of Wiweather sensor.
To reset the sensor, simultaneously press the SEL and SET buttons of the sensor for
2 seconds. All LEDs light on and the sensor is back to the factory programming.
▷ Maximum number of memorable Wireless Sensors
The control board can only memorize 1 Wireless Sensor. Programming a new Wireless
Sensor will delete the previously memorized code.
▷ Poor communication of the Sensor
In case of poor communication between the Wireless Sensor and MC7 control board,
the opening/closing will be automatically activated after 30 minutes. If poor of
communication continues, other remote controls will keep the control board in a state
of security, not allowing the opening of the awning (when receives opening order, it
opens a little bit and returns to the point of closed).
T. MOT. (Programming working time - 4 minutes max.)
The control board is supplied with
LED T.MOT. OFF,
meaning that the motor time is 3
minutes. With T.MOT LED. OFF and the remote control programmed, we can move the
awning in the opening/closing direction, until you make the adjustment of the limit
switches. Follow the instructions. The Working Time must always be set.
The programming of the motor time must be performed with the awning fully
open
Motor time programming with limit-switch in the opening/closing direction is
realized as follows:
With the awning fully open and the opening/closing limit-switches regulated, use the
If you want the same button to open and close, do the programming pressing twice the
same button.
Programming the wireless sensor without access to control board is performed as
follows:
Press continuously, for longer than 10 seconds, the opening channel of a previously
stored transmitter. At the same time the control board enters into programming mode
(indicated by the flashing of the awning lighting lamp). Use the sensor‘s SEL button to
make the LED CODE flash. Immediately press for more than 3 seconds the sensor SET
button. The LED CODE will quickly flash. At this point you are informed of the
programming success signaled by flashing of the awning light.
▷
MC7
Cancellation Codes
The cancellation of all codes memorized for the functioning of awning (remote controls and
Wireless Sensor), proceed as follows: press the SEL button, LED CODE will flash, and then
press the SET button for less than 1 second, LED CODE turns off and the procedure ends.
If necessary, restore the control board to the initial factory settings, press the SEL and SET
buttons at the same time and the LED display will be lit temporarily, confirming the success
of the operation.
If you have been reached the memory limit (14 codes), repeating the programming
operation. All iLEDs will flash quickly, signaling that other memorizations are not possible.
SEL button to make the LED T.MOT blink.
Press continuously the SET button until the
awning closes and the motor stops by the
limit-switch‘s action. Wait two more
seconds and release the SET button. The
LED T.MOT will be lighten and the motor
time will be programmed.
▷ Menu 2
The control board is supplied by the
manufacturer with PGM function
active/On.
To disable press the SET button
continuously for 5 seconds. An alternating
flash of the LED T. MOT starts, and it is
possible now to activate or deactivate the
PGM. With the SEL button, position the
flashing on the LED CODE. Use the SET
button to enable or disable the PGM
function. After 30 seconds, the control
board returns to the main menu.
CODE PGM
Programming a new remote control or Wireless Sensor
The control board allows programming of another remote control, without intervening
directly in the control board, performing the operation at a distance. The programming code
of a remote control at distance, is carried out as follows: with the awning open and the
awning lighting off press continuously, for longer than 10 seconds, the opening of a channel
remote control previously memorized.
At the same time the control board enters into
programming mode. Press for 3 seconds the new transmitter closing button and then
press for another 3 seconds the opening button. At this time the transmitter is
programmed.
05
.
MC7 CONTROL BOARD
06
.
TROUBLESHOOTING
INSTRUCTIONS FOR CONSUMERS AND SPECIALIZED TECHNICAL ◁
▷ PROGRAMMING
The awning does
not stay leveled
after opening.
The top does not
close on one side.
Natural extension of the fabric.
The awning does
not hold correctly
on the wall.
The screws are not suitable for
the wall structure.
Changes in the awning after
several maneuvers.
Improper adjustment on top or
the articulated arms.
▷ Check the installation dimensions
which are on the
pages
03.B e 04.A
.
▷ Verify if the quantity of screws is
sufficient and are indicated in this
manual (
page 04.A
).
▷
Check the level of wall brackets (
nº8
).
▷
Correct the arms inclination considering the
manual's instructions (
página 05.B
).
▷ Adjust the arms (
página 05.B
).
▷ Adjust the limit switches of the motor
(
página 06.B e 10.A
).
▷ Put a plastic shim, on the side where the
fabric suffers the changes between the
tube and the fabric. If necessary add more
shims until the fabric to meet with the
normal extension (
image 27
).
The top does not
close completely.
The awning does
not work and the
motor does not
make noise.
The motor goes into thermal
protection after 2 openings and
1 closure.
▷
Wait 20 minutes.
▷
Check the motor connection.
▷
Check the operation of the motor,
connecting directly into electric current
(
image 28
).
Problem of protection.
The awning does
not work and the
motor does not
make noise.
Problems
Causes
Solutions
Detuning the top or limit
switch.
