Motomaster 011-1975-8 Instruction Manual Download Page 6

Page: 6 / 16

AC ELECTRICAL CONNECTIONS
PLUGGING CHARGER IN

Your charger requires a 120 V AC electrical wall outlet receptacle installed according to local
codes and ordinances.

An extension cord should not be used unless absolutely necessary. Use of an improper
extension cord could result in a risk of fire and electric shock. If an extension cord must be
used, make sure:

USING AN EXTENSION CORD

The pins on plug of extension cord are the same number, size, and shape as those of plug on
charger.

The extension cord is properly wired and in good electrical condition.

The wire size is large enough for AC ampere rating of charger as specified in the chart below:

Model no. 011-1975-8 l Questions? Contact us 1-888-942-6686

SAFETY

MINIMUM RECOMMENDED EXTENSION CORD

Length of Cord, Metres (Feet)

AWG* Size of Cord

7.6 (25)

15.2 (50)

30.5 (100)

45.6 (150)

*AWG = American Wire Gauge

Summary of Contents for 011-1975-8

















Search results

Summary of Contents for 011-1975-8

Reviews:

Related manuals for 011-1975-8

Brands by name

Popular brands

Motomaster 011-1975-8, Instruction Manual

Search results

Summary of Contents for 011-1975-8

Reviews:

Related manuals for 011-1975-8

Brands by name

Popular brands