background image

Thank you very much for purchasing a high quality 

motogadget

 product - Made in Germany.

CAUTION! 

THIS PRODUCT OPERATES ON STRONG CURRENTS. CONNECTION FAILURE MAY LEAD 
TO CABLE FIRE OR EXPLOSION OF THE VEHICLE’S BATTERY. THERE IS A RISK OF 
SEVERE OR LETHAL INJURIES.

IF YOU ARE NOT A CERTIFIED MOTORCYCLE TECHNICIAN, PLEASE STOP HERE AND ASK 
YOUR LOCAL MOTORCYCLE SHOP FOR PROFESSIONAL INSTALLATION.

SEMICONDUCTOR SWITCHES IN USE! MEASURED VOLTAGES AT TERMINALS ARE NOT 
SUITABLE TO DIAGNOSE A FAILURE OR DEFECT.

MOUNTING ON UNEVEN FACES WILL CRACK THE HOUSING AND CAUSE A FAILURE.

Please read the following information and recommendations 

thoroughly

 and follow these in-

structions during installation and use. No liability shall be assumed by motogadget for damage 
or defects resulting from negligence or failure to follow the operating and installation guide.

Contact:

motogadget GmbH
Wollenberger Str. 4i/j
13053 Berlin
Germany

Tel. +49 (0)30 6900410-0
www.motogadget.com
[email protected]

Copyright © 2009-2023 by 

motogadget

 GmbH, Berlin 

motogadget 

and 

mo.lock

 are registered trademarks of 

motogadget

 GmbH, Berlin, Germany.

Summary of Contents for mo.lock NFC













Reviews: