MOTO GUZZI QUOTA 1100 ES Owner'S Manual Download

Page: 42 / 48

MOTO GUZZI

•

Quota 1100 ES

•

Owner’s Manual

ELECTRICAL
EQUIPMENT

The electrical equipment consists of the following:

Battery.

Starter motor with electro-magnetic ratchet.

Generator-alternator fitted to the front of the crankshaft.

Fuel reserve signal device.

Light switch.

Ignition coil.

Electronic control unit (I.A.W. 15 M).

Phase and revolution sensor.

Blinker unit

Voltage regulator.

Fuse box (no. 6, 15 A fuses).

Electronic control unit.

Pump control microswitch, coils, electro-injectors.

Starter microswitch.

Headlight.

Tall light.

Direction indicators.

Selector indicators.

Light direction indicator, horn and headlamp flasher switch.

Hazard warning lights, switch.

Starter and stop device.

Electric horns - Horn switch.

Battery

The battery has a voltage of 12 V and a capacity of 13 Ah; it is charged by the generator.

To reach the battery, remove the right-hand side panel. This is a hermetic (maintenance
free) battery that does not require any electrolyte level control or topping up.

Instructions for recharging
To recharge the battery, use a constant voltage charger set to 14.7 ÷ 15V at 25°C.

WARNING

Summary of Contents for QUOTA 1100 ES

















































Search results

Summary of Contents for QUOTA 1100 ES

Reviews:

Related manuals for QUOTA 1100 ES

Brands by name

Popular brands

MOTO GUZZI QUOTA 1100 ES, Owner'S Manual

Search results

Summary of Contents for QUOTA 1100 ES

Reviews:

Related manuals for QUOTA 1100 ES

Brands by name

Popular brands