background image

MOTO GUZZI 

 Quota 1100 ES 

 Owner’s Manual 

RUNNING-IN 

The recommendations below should be followed when running-in: 

 

Before riding, run the engine at low revs until it has warmed up. 

 

Do not exceed the rpm shown in the table; it is also advisable to run the engine at 
varying speeds rather than at a constant speed. 

 

Before stopping reduce the speed gradually to avoid subjecting components to 
sudden changes in temperature. 

 

Remember that components need several thousand kilometers before they are 

properly bedded in; care taken in this period will ensure prolonged vehicle life. 

After the first 500÷1,500 km 

 

Change the engine oil. 

Should the oil level drop to the minimum level before the first 500÷1,500 

kilometers have been completed then carry out a complete oil change rather than 
just topping up. Recommended oil: 
«Agip 4T SUPER RACING SAE 20W/50». 

 

Replace gear lubrication oil. 

 

Replace transmission box lubrication oil. 

 

Check that all nuts and bolts are tight. 

 

Check rocker clearance. 

 

Check tire pressures. 

Breaking-in RPM 

Kilometers Max. 

RPM 

From 0 to 1,000 

5,000 

From 1,000 to 2,000 

6,000 

From 2,000 to 4,000 

Gradually increase rpm until maximum 

permissible is reached. 

22 

Summary of Contents for QUOTA 1100 ES

















































Reviews: