manualshive.com logo in svg

Motion 4 Doors EvoDrive+, Maintenance Manual, Page: 6 / 12

Share
Download
Motion 4 Doors EvoDrive+ Maintenance Manual Download Page 6

5

v1.0.0

i.

ii.

iii.

iv.

E maintenance manual

GB

5. DETAILED TROUBLESHOOTING

Motor signaling errors

All the errors codes are 

showed blinking in the motor 

display

Error 1 - Code 01 blinking: 

The system has detected an overcurrent, restart the auto-

matic guide and if the error persists contact your dealer indicating the error code.

Error 2 - Code 02 blinking: 

The system has detected an encoder error, verify that the 

motor has magnets during the entire journey, if not, restart the automatic guide and if the 

error persists contact your dealer indicating the error code.

Error 3 - Code 03 blinking: 

The system has detected a weight error, verify that: the leaf 

does not exceed 

80 kg

; the friction of the floor guide is not excessive and the leaf can be 

moved manually throughout its travel.

Error 4 - Code 04 blinking: 

The system has detected an over-temperature error, verify 

that it is not in an environment with a temperature higher than 40 ºC.

Summary of Contents for EvoDrive+













Reviews:

No comments