MORTEX
PRODUCTS
INC
FORT
WORTH,
TX
76106
Page
3
12.
These instructions cover minimum requirements and
conform to existing national standards and safety codes.
In some instances these instructions exceed certain local
codes and ordinances, especially those who have not kept
up with changing mobile home, modular home and HUD
construction practices. These instructions are to be
followed and are the minimum requirement to perform
service or repairs on this appliance.
SECTION III: OWNERS INFORMATION
AND SEASONAL INFORMATION
How the Furnace Works
This furnace may be installed in the downflow position.
Figure 1 shows a typical model in the downflow position. The
furnace is equipped with a motor time delay, transformer,
circuit breakers, and a blower assembly. The transformer
provides 24 VAC to the thermostat. When the thermostat calls
for heat the relay(s) energize sending 240 VAC thru the limit
switches to the electric heaters causing them to get hot. The
indoor fan motor is then energized on the low speed tap and
the circulating blower draws cool air from the living space(s),
passes it across the heater coils and circulates the warmed air
through the duct work to the living space(s). When the
thermostat is satisfied the electric heaters are de-energized.
The blower is also de-energized and the heating cycle has
ended and the furnace is ready for the next call for heat to start
the next cycle.
The furnace is equipped with the controls necessary for proper
and safe operation. Circuit breakers and fuse location are
shown in Figure 1.
Examination of the furnace
The home owner should perform a visual examine the furnace
every month for any defects or problems. The items to be
inspected are:
1.
The physical support of the furnace is sound without
sagging cracks, gaps, etc. around the base so as to provide
a seal between the support and the base.
2.
The furnace casing for any obvious signs of deterioration
from rust or corrosion.
3.
The return and supply duct connections are physically
sound and are sealed to the furnace casing.
4.
The furnace must be serviced by qualified personnel
annually, preferably at the start of each heating season.
Figure 1: Circuit Breaker Locations
The Service Technician
The furnace’s best friend is a qualified service technician. If
the unit gives any indication of improper operation, call the
service technician. The service technician is allowed to
perform the normal routine care of your furnace. He can detect
potential problems and make corrections before trouble
develops. Preventative maintenance of this type will allow the
furnace to operate with minimal concerns to the homeowner
and will add years of comfort.
Warranty and Responsibilities
It is the sole responsibility of the homeowner to make certain
the furnace has been properly installed and adjusted to operate
properly.
The manufacturer warrants the furnace to be free from defects
in material or workmanship for a stated time in the warranty
agreement. The manufacturer will not be responsible for any
repair costs to correct problems due to improper setup,
improper installation, improper furnace adjustments, adding
parts that are not listed for use with this furnace, improper
operating procedures by the user or repairs performed by the
user / owner.
Some specific examples of service calls which will be
excluded from warranty reimbursement are:
1.
Correcting faulty duct work in the home. This can be due
to not enough ducts or ducts are too small to provide
proper air flow through the furnace.
2.
Correcting wiring problems in the electrical circuit to the
furnace.
3.
Resetting circuit breakers or on/off switches used for
servicing.
4.
Furnace problems caused by installation and operation of
any air conditioning unit, heat pump, or other air quality
devise which is not approved for use with this furnace.
5.
Adjusting or calibrating the thermostat.
6.
Problems caused by construction debris which has fallen
into the furnace.
7.
Replacement of fuses.
8.
Problems caused by dirty air filters.
9.
Problems caused by restrictions in the return or supply air
flow causing low air flow.
FIRE OR ELECTRICAL HAZARD
Servicing heating/cooling equipment can be hazardous due
to electrical components.
Only trained and qualified personnel can service or repair
heating/cooling equipment. The home owner
must never
try
to perform service, repair or maintenance on this appliance.
Untrained service personnel can perform only basic
maintenance functions such as cleaning of exterior
surfaces and replacing the air filters.
Observe all precautions in the manuals and on the attached
labels when working on this appliance