background image

16

The Telefl ex Marine division of Telefl ex Incorporated, (“Telefl ex Marine”) warrants its products to be free from defects in materials and 
workmanship for a period of two years from the date of original retail purchase, provided, however, the warranty period for Telefl ex 
Marine products used commercially or in any rental or other income producing activity shall be as follows:

•  Ninety days from the date of original purchase for mechanical and electrical products; and
•  One year from the date of original purchase for hydraulic products.

We will provide replacement product without charge for any Telefl ex Marine product covered by this warranty, which is returned 
(freight prepaid) within the warranty period to the dealer from whom such products were purchased, or to us at the appropriate 
address. In any such case, Telefl ex Marine products found to be defective and covered by this warranty will be replaced or repaired at 
Telefl ex Marine’s option, and returned to the customer. Telefl ex Marine’s sole responsibility under this warranty is limited to the repair 
or replacement of product which is, in Telefl ex Marine’s opinion, defective. Telefl ex Marine is not responsible for charges connected 
with the removal of such product or reinstallation of replacement or repaired parts.

We will have no obligations under this warranty for any product which:

•  has been improperly installed;
•  has been used in an installation other than as recommended in our installation or operation instructions or specifi cations;
•  has failed or has been damaged due to an accident or abnormal operation including racing, misuse or alterations outside our 

factory;

•  has been repaired or modifi ed by entities other than Telefl ex Marine;
•  has been used on an engine/boat combination where the engine horsepower exceeds the rating established by the boat 

manufacturer;

•  has been used with other product(s) which, in Telefl ex Marine’s opinion, are incompatible with the Telefl ex Marine product.

THE EXPRESS WARRANTY SET FORTH ABOVE IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT 
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TELEFLEX MARINE 
EMPLOYEES OR REPRESENTATIVES’ ORAL OR OTHER WRITTEN STATEMENTS DO NOT CONSTITUTE WARRANTIES, SHALL NOT BE 
RELIED UPON BY CUSTOMER, AND ARE NOT A PART OF THE WARRANTY STATED HEREIN. THIS WARRANTY WILL BE THE CUSTOMER’S 
EXCLUSIVE REMEDY. IN NO EVENT WILL TELEFLEX MARINE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR 
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS. Some states to not allow limitations on an implied 
warranty, or the exclusion of incidental or consequential damages, so the above exclusions may not apply to you. You may also have 
other rights which vary from state to state. 

If any part of this Limited Warranty is determined to be void or illegal, the remainder shall remain in full force and effect.

Telefl ex Marine products returned under this warranty must be tagged with the customer’s name, street address, and phone number to 
ensure proper handling, and returned freight prepaid to the selling dealer or to the appropriate Telefl ex Marine manufacturing facility.

Warranty Items — Telefl ex Mechanical, Electrical, Hydraulic Only:

Telefl ex Marine fi eld representatives are authorized to investigate any allegedly defective merchandise in the fi eld. They can request 
credit, disposal, and/or return of these products during the course of their regular visits to the customer’s facilities once they have the 
facilities approval.

brand controls are products of

Teleflex Marine   640 North Lewis Road   Limerick, PA 19468   USA   Tel:  610-495-7011   

www.teleflex.com

Summary of Contents for SL-3

















Reviews: