background image

Safety Information (continued)

DANGER

 - Indicates a situation which, if not avoided, 

will

 result in se-

rious injury or death.  This signal word is limited to the most extreme 

situations.

WARNING

 - Indicates a situation which, if not avoided, 

could

 result in 

serious injury or death.

CAUTION

 

- Indicates a situation which, if not avoided, can result in dam-

age to the machine.

CAUTION

 

– Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. 

 The unit 

can become unstable when transporting with a raised load.

DANGER

 - Stay Clear of Power Lines

KEEP WELL CLEAR OF POWER LINES. 

 Never approach a power line.  Current in a high voltage line may 

arc some distance from the wire to the steel framed, grounded machine.

WARNING

The Hydra-Lift Karrier is designed to handle one drum of the types listed at the top of page 3, under 

2.  

Machine Description

.  

DO NOT

 attempt to handle any other type of drum or object.  

DO NOT

 exceed the 

weight capacity of 800 Lb.

WARNING

 

- Level Floors Only

For operation only on clean, level floors of suitable bearing capacity. Do not use on sloped surfaces, ramps, 

irregular or debris strewn floors.

WARNING

 - Do Not Modify the Unit

Under no circumstances should any modifications be made to the Morse machinery without factory authori

-

zation.  Any modifications may void the warranty.  This machine was designed to perform a specific job and 

alterations may result in injury to operator or machine.

WARNING

 - No Loose Fitting Clothing

Wear close-fitting clothing and safety equipment appropriate to the job.  Loose fitting clothing may become 

caught on the machinery and cause severe personal injury.

WARNING

 - Hydraulic Fluid Under Pressure Can Be Hazardous

Escaping hydraulic fluid under pressure can penetrate the skin, causing serious injury.  Avoid the hazard 

by relieving pressure before disconnecting hydraulic lines.  Keep hands and body away from pinholes and 

nozzles, which eject fluid under high pressure.  Use a piece of cardboard to search for leaks. If an accident 

occurs, see a doctor immediately and inform them of the nature of the accident.

CAUTION

 - Wear Safety Shoes

Wear safety shoes with non-slip soles and hard toe protection.

Copyright 2009  -  Morse Mfg. Co., Inc.   

Form PL400M-72 (0804-0309)   (Updated 12/2009) 

 

Page 2

Operator’s Manual for Morse Hydra-Lift Drum Karrier with Spark Resistant Parts

Model 400AM-72

Serial Number 0804 to 0309 (MMYY)

The Specialist In Drum Handling Equipment

Model 400AM-72

Hydra-Lift, 72”, Manual Lift, Manual Tilt

with Spark Resistant Parts

Summary of Contents for 400AM-72












Reviews: