background image

The Specialist In Drum Handling Equipment

Model 400A-96SS-125

Stainless Steel Hydra-Lift Karrier, 96”, 

DC Power Lift, Manual Tilt

Operator’s Manual for Morse Model 400A-96SS-125

Serial Number 1210 to ____ (MMYY)

morsedrum.com

Copyright 2022 - Morse Mfg. Co., Inc. 

 

Form OM400A-96SS-125 (1210-____)  

(Updated 3 Mar., 2022)

 

5

Operating Instructions

1.)  Push the Hydra-Lift Karrier to the drum.

2.)  Using the “LIFT” control as described in “

Machine 

Description - Controls

”, position the drum holder 

assembly with the back band at the middle of the drum. 

(Figure 3.1).  With the ratchet plate swung open and 

the cinch chain hanging from the chain hook, push the 

unit until the back band rests firmly against the drum.  

Some adjustment to the tilt angle of the saddle may be 

necessary to ensure band fits flush on the drum.

3.) 

Attaching the drum:

Drape the chain across the front of the drum and engage 

a link into the slot in the ratchet (Figure 3.2).  Turn the 

ratchet clockwise to tighten chain.  If ratchet turns until 

the pawl is beyond the last ratchet tooth, turn the ratchet 

back and slide the next link into the ratchet slot and try 

tightening again.  The chain must be held tightly against 

the drum with the pawl engaged securely in the ratchet 

teeth.

4.) Operate the lift function to lift drum clear of floor.  Roll to 

dispensing location.  NOTE: Do not allow the drum to 

impact on floor, pouring station, etc. or a spill or damage 

could occur.

START-UP Procedure

Machine is shipped with hydraulic fluid. 

1. 

Install provided hydraulic control levers (threaded rods with black ball handles).

 

2.  IMPORTANT:

 BEFORE operation, remove the 

RED

 shipping plug from the hydraulic reservoir, and replace with the 

provided 

BLACK

 breather.

CAUTION

 

– Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. 

  

The unit can become unstable when transporting with a raised load.

5.) Lift drum to desired pouring height.  Operate the tilt control as described in 

“Machine Description - Controls”

 to 

adjust the drum attitude. This is especially important when lifting an open drum.  The floor lock should be engaged while 

dispensing / draining.

Figure 3.2

Summary of Contents for 400A-96SS-125







Reviews: