4
•
When using the extension cable, make sure that it does not
interfere, is not squeezed or bent, and the plug does not get
wet.
•
When using a cable reel, wind the cable completely off the reel.
•
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the machine. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
•
Check the extension cable regularly for damage to the
insulation. Replace it if damaged.
•
Before inserting the plug in the mains socket, make sure
that the socket ratings are correct and correspond to those
indicated on the rating label on the shredder.
•
Always disconnect the machine from the mains supply before
transporting it to other places.
•
Always switch off the shredder before disconnecting any plug
and socket connector or extension cables.
•
Never leave the shredder unattended while it is switched on.
•
Before leaving the shredder, switch off the motor and
disconnect the plug. Do likewise in the event of a power failure.
•
Keep children and pets away. All onlookers should be kept a
safe distance away from the shredder when it is in use.
•
Do not allow children or any person who has not read this
instruction leaflet or who is not familiar with the shredder to
operate it.
•
The operator is responsible for third parties while working with
the shredder.
•
Only use the shredder for its designed purposes.
•
Never deactivate or bypass the protective devices.
•
When using the machine outdoors, always use a residual
current-operated circuit-breaker (RCD) with an operating
current of 30 mA or less.
Operation
•
The appliance is not to be used by persons (including children)
with reduced physical, sensory or mental capabilities, or lack
of experience or knowledge, unless they have been given
supervision or instruction.
•
Children must be supervised not to play with the appliance.
•
Keep your face and body away from the inlet opening.
•
Never let your hands or other part of the body or clothing be
placed inside the inlet and discharge opening, or near moving
parts. It may result in serious injury.
•
Do not overreach. Keep proper footing and balance at all
times. This enables better control of the machine in unexpected
situations. Do not stand at higher level than the base of the
machine when feeding material into it.
•
Always keep distance from the discharge opening during
operation.
•
Observe regional regulations for noise protection.
•
Do not feed rock, a piece of metal, bottles or other foreign
matter. Pay attention that those foreign objects are not included
when you feed.
•
Immediately switch off the motor and unplugged if the blade
strikes a foreign object or the machine starts vibrating or
making unusual noise. Check the shredder for damage, and
tighten any loose parts. Ask an authorized service center to
repair the machine.
•
Do not let the processed material accumulate in discharge
opening. Otherwise it may result in kickback of material through
the inlet opening.
•
Switch off the motor and unplug before:
-
Leaving the machine unattended
-
Before clearing a blockage or any fault
-
Before checking, cleaning or working on the
-
machine
-
Before making any adjustments, changing
accessories or storing
-
Whenever the machine starts vibrating or making
unusual noise
-
Clearing inlet or discharge opening
-
Attaching or removing retaining basket
-
Transporting
•
Do not force the machine. It does the job better and safer at
the rate for which it was designed. Frequent overload may
cause motor damage or fire.
•
Use the right appliance. Do not use appliances for purposes
not intended. Not intended to feed metal parts, glasses,
stones, ceramics, plastics, thicker branches, hard wood or
thick wood plates, etc.
•
Caution! There is a rotating blade on this machine.
•
Caution! Blade does not stop immediately after switching off.
•
Always switch off the shredder, disconnect the plug and wait
until the cutting disc stops before carrying out maintenance or
cleaning work.
•
Use caution when cleaning or performing maintenance on the
shredder. DANGER! Watch your fingers! Wear gloves!
•
Do not move or modify any of the electrical and mechanical
safety devices.
•
The shredder has to stand on level and solid ground during
operation.
•
Use only in daylight or good artificial light.
•
Wear gloves and safety goggles while shredding.
•
We recommend the use of ear muffs.
•
Caution! The hopper must be fitted and tightened completely
before use.
•
Do not put your hands into the feed funnel and ejection slot.
•
During operation ensure that no foreign objects (such as
stones, glass, metal, earth, plastics) are fed into the shredder;
these foreign objects could cause blunting of the blade and
seriously damage the motor. Do not use your shredder for
purposes other than for its intended use.
•
If the shredder should start to vibrate abnormally, switch off
the motor and check for the cause immediately. Vibration is
generally a warning of trouble.
•
Ensure blade is secure before shredding. Do not operate the
shredder if the blade is not properly mounted.
•
The shredder should be checked carefully before use. You
should only work with a shredder that is in good condition. If
you notice any defect on the machine that may cause danger
to the operator, do not operate the shredder until defects are
rectified.
•
Replace worn or damaged parts for safety. Use only original
spare parts. Parts not produced by manufacturer may cause
poor fit and possible injury.
•
Use the shredder only in places where it is protected from
water and never use it outdoors in rainy weather.
•
Store in a dry secure place out of reach of children.
Warning!
Failure to adjust the cutting plate correctly can cause
damage to the machine. If required, adjust the cutting
clearance following instructions on page 8.
Maintenance instructions
•
Have your machine serviced by our authorized service centre,
always using only genuine replacement parts.
•
Incorrect repair and poor maintenance can shorten the life of
the machine and increase the risk of accidents.
•
Before servicing, inspection, adjustment, storage, or to change
an accessory, take following steps:
-
Shut off the power source
-
Disconnect the machine from power supply
-
Make sure that all moving parts have come to a
complete stop
-
Allow the machine to cool.
