background image

MORNINGSTAR CORPORATION

37

4.0  OPERATION

36

will depend on many factors including:

• 

rate of discharge (amount of load draw)

• 

capacity of the battery

• 

health of the battery

• 

LVD set-point

If the battery discharges to the LVD set-point the load will 

disconnect and a solid red Battery Status LED indication will 

be displayed.

General Load Control Notes

•  Only SS-6L/10L/20L models provide load control.
•  Regulated voltage due to temperature compensation 

is limited to a maximum of 15V (30V @ 24V nominal). 

This protects certain DC loads that may be damaged 

by high regulated input voltage. 

•  The load connection is NOT a regulated voltage 

output. The load terminal voltage is approximately the 

same as battery voltage unless the controller is in LVD 

condition (load turned off).

•  Do not wire multiple SunSaver load outputs together in 

parallel to power DC loads with a current draw greater 

than the lowest rated controller’s maximum load rating. 

Equal current sharing cannot be guaranteed and an 

over-load condition will likely occur on one or more 

controllers.

• 

Exercise caution when connecting loads with specific 

polarity to a live load circuit. A reverse polarity con-

nection may damage the load. Always re-check load 

connections before applying power.

•  The SunSaver will go straight to LVD on start-up if the 

battery voltage is at or below 11.7V / 23.4V.

 4.0

4.4 Protections

Solar Overload

(Charging Status LED: Red flashing) If the solar current 

exceeds the maximum solar rating, the SunSaver will 

stop charging until the solar current returns to within its 

operational rating. See 

Section 7.0 Technical Specifications

 

for more information.

Load Overload 

(Battery Status LEDs: G&R - Y sequencing) If the load 

current exceeds the maximum load current rating, the 

SunSaver will disconnect the load.

The SunSaver will attempt to reconnect the load two 

(2) times approximately 10 seconds apart. If the overload 

remains after the first two (2) attempts, the fault must be 

cleared by removing and reapplying power.

Solar Short Circuit 

(Charging Status LED: off) Solar input power wires are 

short-circuited. Charging automatically resumes when the 

short is cleared.

Load Short Circuit

(Battery Status LEDs: G&R - Y sequencing) Fully 

protected against load wiring short-circuits. After two (2) 

automatic load reconnect attempts (10 seconds apart), the 

fault must be cleared by removing and reapplying power.

PV Reverse Polarity

(Charge Status LED: off)  Fully protected against reverse 

solar connection. No damage to the controller will result. 

Correct the mistake to resume normal operation.

Summary of Contents for SUNSAVER SS-10-12V



























Reviews: