Morgana AutoCreaser 50 Operator'S Manual Download | Manualshive

Page: 26 / 35

background image

Replacing Blade Set

11.

Push the exit guard down and replace the stacker assembly before operating the
machine.

12.

Switch the machine on and test the crease for form.

If the pressure and the alignment of the crease is not to a satisfactory level,
see pages 23 –25 to adjust the creasing line.

‘Spares’ kits

In the event of any damaged or lost components within the blade assembly, spares kits
are available on request. However, components within the blade set can not be ordered
separately ie single blade or anvil.

Standard Blade set

Part number 76-237-02

Consisting of a standard blade and anvil, blade brushes, blade links and alignment bolts.

FIG 21.1

Narrow Blade set

Part number 76-237-03

Consisting of a narrow blade and anvil, blade brushes, blade links and alignment bolts.

Page 26

CREASING

«
...
24
25
26
27
28
...
»

Summary of Contents for AutoCreaser 50




































Reviews:

No comments

Related manuals for AutoCreaser 50

Brand: Fastbind Pages: 3

Brand: Antari Pages: 10

SircleBind CB-3000

Brand: Sircle Pages: 6

Brand: ELNA Pages: 2

Brand: QTX Light Pages: 7

Brand: Kärcher Pages: 16

Brand: Sagem Pages: 44

Memory Craft 200E

Brand: Janome Pages: 54

Brand: Sase Pages: 76

Brand: Janome Pages: 96

Brand: Dürkopp Adler Pages: 374

Brand: Olivetti Pages: 16

Brand: Racing Pages: 3

Brand: Rustibus Pages: 31

Brand: HIGHLEAD Pages: 39

Brand: Neopost Pages: 11

Brand: Pacific Floorcare Pages: 24

Brand: Electrolux Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands