background image

1. Do not locate the Module facing direct sunlight, humid or dusty place.

2. The suitable ambient temperature for the Module is 0°C~40°C.

3. Do not locate the Module where exists combustible substances or any source of

heat, e.g. fires, radiators, boiler etc. 

4. After putting it into use, the body of Module will become a little bit hot of which

phenomenon is normal. 

Warning: 

1.Plug out to disconnect from power supply; Do not plug in line. 

2. Do not exceed the max rating.

Disposal 

This marking indicates that this product should not be disposed with 
other household wastes throughout the EU. To prevent possible harm to 
the environment or human health from uncontrolled waste disposal, 
recycle it responsibly to promote the sustainable reuse of material 
resources. To return your used device, please use the return and 
collection systems or contact the retailer where the product was 
purchased. They can take this product for environmental safe recycling. 

Choosing a Suitable Location 

 However, there is no guarantee that interference will not occur in a particular 

installation.  

If this equipment does cause harmful interference to radio or television reception, 

which 

can be determined by turning the equipment off and on, the user is encouraged to try 

to correct the interference by one of the following measures: 

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject 

to the following two conditions: 

(1) This device may not cause harmful interference, and 

FCC Interference Statement 

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful 
interference in a residential installation.  
This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. 

(2) This device must accept any interference received, including interference that 

may cause undesired operation. 

FCC Caution: Any changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to operate this equipment. 

This transmitter must not be co-located or operating in conjunction with any other 

antenna or transmitter. 

www.mordomus.com

Summary of Contents for iZ2EM

Page 1: ... the network Mini size design let the module can easily hide itself into the electricity distribution box and that will be good for the house decoration This dual meter module is able to detect Instant power wattage 13800W 230Vac 60 Amperes of connected light or appliances Adding to Z WaveTM Network In the front casing there is an on off button with LED indicator below which is used to carry out i...

Page 2: ...ressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode Use this procedure only in the event that the primary controller is lost or otherwise 2 Within 1 second press Include button again for 5 seconds inoperable 3 IDs are excluded LED 0 5s On 0 5s Off Enter auto inclusion Association 1 The iZ2EM is an always listening Z Wave device so associations be added or removed by a con...

Page 3: ... up the meter and send it for repair The meter cannot report to the group 1 Not carry out association 2 Same frequency interference 1 Carry out association 2 Wait for a while to re try Specification Operating Voltage Rated Primary Current Range Operating Temperature Frequency Range 100 240VAC 0 05A 60A x 2 Channel Split Core Transformer Minimum 40 m in door 100m outdoor line of sight 0 C 40 C iZ2E...

Page 4: ...f and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with P...

Reviews: