background image

Description 

ISA 1 

Rev. -, April 2019 

 

Hot surface warning 
The drive may become hot during operation. 

 

Voltage warning 
There is voltage present inside the housing. 

 

The nameplate informs about the exact type of the drive and the most important perfor-

mance data of the sliding system drive. 

3

 

Description 

 

Fig. 2

 

Structure of the sliding system drive 

1  Communication ports I/O  

5  Logic component with housing 

2  DIP switch for addressing 

6  Operating mode selector switch 

3  Servomotor  

7  Mains connection 

4  Gearbox with pinion shaft 

8  Communication ports to other drives 

3.1

 

Structure of the sliding system drive 

The sliding system drive consists of a servomotor (Fig.

 

2/3), a logic component with  

housing (Fig.

 

2/5), and a gearbox (Fig.

 

2/4). Via the communication ports (Fig.

 

2/1) and the 

mains connection (Fig.

 

2/7) at the back of the housing, the sliding system drive is con-

nected to the peripherals provided by the customer and the power supply. Additional 

drives can be connected via the other communication ports (Fig.

 

2/8). 

Summary of Contents for ISA1 Series

















Reviews: