Moog Videolarm PFD75C2N Product Instructions Download Page 2

!

  

Caution

Risk of 

ElECtRiC shoCk!

  

Caution:  to REDuCE thE Risk of 

ElECtRiCal shoCk, Do not EXPosE  

CoMPonEnts to WatER oR MoistuRE.

safEtY PRECautions

iMPoRtant safEGuaRDs

1. 

Read Instructions

 - All the safety and operating  instructions should be read 

before the unit is operated.

2. 

Retain Instructions

 - The safety and operating  instructions should be retained 

for future reference.

3. 

Heed Warnings

 - All warnings on the unit and in the operating instructions 

should be adhered to.

4. 

Follow Instructions 

- All operating & user instructions should be followed.

5. 

Electrical Connections

 - Only a qualified electrician should make electrical 

connections.

6.  

Attachments

 - Do not use attachments not recommended by the product 

manufacturer as they may cause hazards.

7. 

Cable Runs

 - All cable runs must be within permissible distance.  

8. 

Mounting

 - This unit must be properly and securely mounted to a supporting 

structure capable of sustaining the weight of the unit.  Accordingly:

a.  Installation should be made by a qualified installer.

b.  Installation should be in compliance with local codes.

c.  Care should be exercised to select suitable hardware to install the unit, 

taking into account both the composition of the mounting surface and 

the weight of the  unit. Be sure to periodically examine the unit and the 

supporting structure to make sure that the integrity of the installation 

is intact.  Failure to comply with the foregoing could result in the unit 

separating from the support structure and falling, with resultant damages 

or injury to anyone or anything struck by the falling unit.

unPaCkinG

  Unpack carefully.  Electronic components can be damaged if improperly handled 

or dropped.  If an item appears to have been damaged in shipment, replace it 

properly in its carton and notify the shipper.  

Be sure to save:

1.  The shipping carton and packaging material.  They are the safest material in 

which to make future shipments of the equipment.

2.  These Installation and Operating Instructions.

!

The lightning flash with an arrowhead symbol, within an 

equilateral triangle, is intended to alert the user to the 

presence of non-insulated "dangerous voltage" within the 

product's enclosure that may be of sufficient magnitude 

to constitute a risk of electric shock to persons.

The  exclamation  point  within  an  equilateral  triangle  is 

intended to alert the user to presence of important operating 

and maintenance (servicing) instructions in the literature 

accompanying the appliance.

24 houR tEChniCal suPPoRt

1-800-554-1124

sERViCE

  If the unit ever needs repair service, customer should contact Videolarm 

(1-800-554-1124) for return authorization & shipping instructions.

tEChniCal suPPoRt

  Videolarm has set-up a 24 hour technical support line for their customers.

LIMITED WARRANTY

 

FOR VIDEOLARM INC. PRODUCTS

VIDEOLARM INC. 

warrants this Product to be free from defects in material or workmanship, as follows:

PRODUCT CATEGORY

                                    

PARTS 

 

 

 

 

 

LABOR

All Enclosures and Electronics  

 

Three (3) Years  

 

 

 

Three (3) Years

Pan/Tilts   

 

 

Three (3) Years  **6 months if used in autoscan 

Three (3) Years    **6 months if used in autoscan

Poles/PoleEvators 

 

 

Three (3) Years  

 

 

 

Three (3) Years

Warrior/Q-View/I.R. Illuminators 

 

Five (5) Years 

 

 

 

Five (5) Years

Controllers  

 

 

Three (3) Years 

 

 

 

Three (3) Years

Power Supplies 

 

 

Three (3) Years 

 

 

 

Three (3) Years

Accessory Brackets 

 

 

Three (3) Years 

 

 

 

Three (3) Years

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc. Decatur GA. 

The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA # (Return Materials 

Authorization number) displayed on the outer box or packing slip.  To obtain a RMA# you must contact our Technical Support Team at 800.554.1124, extension 101. 

Videolarm will return the repaired Product freight prepaid to Purchaser. Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty 

period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions:

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE:

 If Purchaser believes that the Product is defective in material or workmanship, then written notice 

with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period. 

If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm for the cost of investigating 

the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire 

Product. The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the 

remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE:

 Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair 

any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: 

Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during 

the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts of God (i.e., hurricanes, 

earthquakes), modification, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance 

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the Product.  

Furthermore, Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts (based on usage) 

and the end-user has failed to follow such schedule; attempted repair by non-qualified personnel; operation of the Product outside of the published environmental 

and electrical parameters, or if such Product’s original identification (trademark, serial number) markings have been defaced, altered, or removed.  Videolarm 

excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser.  

All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where 

expressly provided otherwise in any documentation or license agreement furnished with the Product.

4. PROOF OF PURCHASE: 

The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

 

EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY CLAIM 

OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS 

ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS 

PURCHASER CHOOSES TO CONNECT TO PRODUCT.

LIMITATION OF LIABILITY

 

THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, 

REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH 

SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT 

LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

Summary of Contents for PFD75C2N

































Reviews: