background image

Page 2 of 19

MW38-DV  Modular Fireplace

P/N XG0112

Introduction

About the Wildfire 38:

The 

MW38-DV

 is a direct-vented gas fireplace equipped with a dual-

inlet Wildfire® Burner. It is available in four models:

 

 

 

 

 

Top Vent (Product Code MW38-

DT

)

 

 

 

 

 

Rear Vent (Product Code MW38-

DR

)

 

 

 

 

 

Intermittent Pilot - Top Vent (Product Code MW38-

DT-I

)

 

 

 

 

 

Intermittent Pilot - Rear Vent (Product Code MW38-

DR-I

)

The MW38-DV is rated for Natural Gas at 29,000 BTU/H (8.5
Kilowatts) Input or

 

Propane at 29,000 BTU/H (8.5 Kilowatts) Input

How to use this manual:

This manual covers all models and unless otherwise specified, the
designation MW38-DV refers to all models. Sections which are
specific to a particular model are marked with a

    symbol,

plus the appropriate model number.

Warranty and Installation Information:

The Montigo warranty will be voided by, and Montigo

 

disclaims any

responsibility for, the following actions:

Modification of the fireplace and/or components including Direct-
Vent assembly or glass doors.

Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.

Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation
requirements for factory-built gas fireplaces. Installation & repairs
should be done by a qualified contractor.

Installations in Canada

 must conform to the current 

CAN/CGA B-

149.1

 and 

.2

 Gas Installation Code and local regulations. If the

optional air-circulating fan kit is installed, it must be electrically
grounded in accordance with 

CSA C22.1

 Canadian Electrical Code

Part 1 and/or Local Codes.

Installations in the USA

 must conform to local codes, or in the

absense of local codes to the National Fuel Gas Code, 

ANSI Z223.1-

1988

. If the optional air-circulating fan is installed, it must be

grounded in accordance with local codes or, in the absence of local
codes, with the National Electrical Code, 

ANSI/NFPA 70-1987.

Table Of Contents

Introduction .............................................................................

2

Installation

Installing the Fireplace Shell ......................................... 3

Installing the Gasline ..................................................... 4

The Remote Switch ....................................................... 4

Direct Vent Installation .................................................. 4

General Requirements ...................................... 4

Terminations ..................................................... 5

Top Vent Models with horizontal runs ............... 6

Top Vent Models with vertical runs ................... 8

Rear Vent Models ............................................. 9

Construction around the fireplace

Facing ............................................................. 10

Mantels and Surrounds ................................... 10

Wiring ................................................................ 10 - 11

Installing the Logset .................................................... 11

Removing and Installing the Insert .............................. 11

Removing and Installing the Door ............................... 12

Operation ........................................................................

13 - 14

Maintenance ...................................................................

15 - 16

Warranty .................................................................................

17

Appendix

A. Spare Parts ............................................................. 18

B. Termination Locations ............................................ 19

CAUTIONS

Due to its high operating temperatures, the appliance
should  be located out of traffic & away from furniture and
draperies.

Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.
Young children should be carefully supervised when
they are in the same room as the appliance.
Clothing or other flammable materials should not be
placed on or near the appliance.

Summary of Contents for Wildfire MW38-DV






















Reviews: