Page 3
You must read and understand this manual prior to installation, operation or
troubleshooting this appliance. Please retain this owner’s manual for furure reference
and maintenance.
NOTICE
LDVPV47 Linear Power Vent System
Introduction
XG0750 - 112911
General Information
This installation guide covers installation of the Linear Power Vent System
only. This system is designed to allow installation of gas fireplaces that
cannot be done with a standard Direct Vent gas fireplace installation.
Specifications and instructions pertaining to your chosen fireplace must
be followed. Please read this Installation Operation and Maintenance
Instructions carefully before operating this equipment.
Standard Series (4"/7" dia.) Termination System:
LDVPV47 - Linear Power Vent System
Pre/Post Purge Control Box
RHSIT05 -Control module, provides pre/post purge. (HSI System)
ECB-007 Post Purge control box (IPI System)
Power Cord Harnesses:
LPVH10 -10 foot power cord and harness
LPVH20 -20 foot power cord and harness
LPVH30 -30 foot power cord and harness
LPVH40 -40 foot power cord and harness
LPVH50 -50 foot power cord and harness
LPVH60 -60 foot power cord and harness
LPVH70 -70 foot power cord and harness
LPVH80 -80 foot power cord and harness
Selecting and Installing the Fireplace
The Linear Power Vent System must only be used with a Montigo Direct
Vent Fireplace. When selecting a gas fireplace for use with the Linear
Power Vent System, take into consideration the various requirements and
limitations in the
venting installation section
of the Model's manual:
Models Must Be Equipped with Electronic Ignition
(HSI/IPI)
Only models equipped with an electronic ignition system may be
installed with the Linear Power Vent System. This system allows for
greater flexibility on venting requirements. For example downward
vertical vent runs are possible with an HSI/IPI system, as outlined in
the
Venting Section.
All fireplaces with 5"/8" venting must be reduced to 4"/7" venting
in order to be used with the Linear Power Vent System.
Before You Begin
Minimum clearances of 1" from vent to all combustible materials
must be maintained.
The LDVPV must only be installed with Montigo venting
components. The LDVPV may be used with any of the available
Montigo terminations.
In order to maintain the power vent system integrity all 4"
and 7" venting connections must be fastened with three
self tapping screws.
Installation of the LDVPV must comply with this manual, and be
completed by a qualified professional.
Plan the layout of the installation's venting run before starting
the installation.
The MAXIMUM total allowable length; Refer to Linear Power
Vent Installation Section, Page 4-6.
Downward venting is allowable. Please refer to Page 5 for a
table and illustrations regarding the limitations of this type of
installation.
Minimum length of straight pipe between the Fireplace and the
Power Vent is: 2 feet
Access / Service Panel, must maintain 1" clearance. Minimum
30% free air must be supplied to the motor.
Disconnect the power supply when installing and/or
servicing the fireplace or the power vent system.
When cold air enters warm building interiors, primarily at the air intake end,
condensation may occur on the exterior of the flex pipe. To limit condensation, install
insulation over the last 20 feet of flex pipe. Sloping the last 20 - 0 feet of flex pipe
downward to the exterior of the building may also aid in eliminating condensation.
Ensure the termination is securly fastened and is sealed to the flex pipe. Fasten the
termination to building exterior with water tight sealant and appropriate fasteners.
CAUTIO N
Ensure perforated air holes in the new pipe adapter / restrictor are not covered
when installing new pipe connection.
CAUTION
Due to high operating temperatures, this appliance should be located out of traffic &
away from furniture and draperies.
Children and adults should be alerted to the hazards of the high surface temperature,
which could cause burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the
appliance.
Clothing or other flammable materials should not be placed on or near the appliance.
CAUTION