Monte Carlo Fan Company 5MMR54 D-L Series Installation Instructions Manual Download Page 4

Loosen 3 screws with k ey slots and remove the

screwwithout key slot. 

19

Take plate and place o ver the 3 screws with k ey

slots  and twist to hold in place. R eplace the

screw removed and tighten all 4 screws secure -

ly holding the plate.

20

Plug white wire from fan to white wire  from

light kit. Then plug bl

ack

 from fan to black from

light kit.

21

Attach glass by locating dimples in light kit and

aligning it with the gro ves in glass and twisting

clockwise till tight.

24

Install the 2 X 50 w att halogen bulbs. Do not

touch bulb surface as oily residue from skin can

cause the bulb to explode. Bulbs included.

WARNING: Over lamping the fan will
result in the fan lights shutting down
until the proper wattage of bulbs are
installed. Reset the lights by turning off
the wall switch, breaker,or by remote.
Replace bulbs with the correct wattage
bulbs, turn the power on.

23

If you choose not to use light kit. Loosen 3

screws with key slots and remove the 1 without

slots.  Attach switch cap holder b y placing over

screws and twisting clockwise into place.

Replace screws removed and tighen all screws

securely. Place switch cap co ver over switch cap

holder and tighen screw to hold in place.

25

Remove cover by snaping off from top or bot -

tom. Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 / Eveready

A23 / GP 23A all 12V.Attach cover of remote by

placing over buttons and snap the battery

cover in place.

Place face plate over battery compartment and

buttons. Place remote over 2 pins on front co ver.

Attach cover of remote by placing over 4 pins

and snaping into place.

27

26

HAND HELD INSTALL

Install wall control unit to outlet bo x

using machine screws provided.

28

Attach front cover to wall control

with screws provided. Snap battery

cover in place. 

29

WALL MOUNT INSTALL

Loosen 2 screws and remove 1 screw from light

pan. Save screw for later use. 

Attach light fixture by aligning keyhole slots on

light fixture with screws on light pan and twist

clockwise till lock. Re-install the screw removed.

Tighten all screws securely.   

22

Summary of Contents for 5MMR54 D-L Series













Reviews: