background image

Reference 09Aug2014 – V16

 

Pg 

11 of 12

 

Copyright 2002-2014, Monster Tower, Inc.

 

 

The last step is to double check that all fasteners are tight, including the top section set 

screws and jam nuts tightened against the leg rod end support   The tower is now ready 

for use.  The Monster Tower IS ABSOLUTELY SILENT when installed correctly.  Shake 

the tower and if you hear any noise check all the hardware and make sure it is tight.  If 

you hear any noise or rattling at any time, something is wrong, please correct it or call 

us before using the tower. 

Thank you again for your business and if we can be of assistance in any way please call 

us at 877-77-Tower or email us at 

[email protected]

 

 

Remember to send us a few pictures of your boat with the Monster Tower 

installed AND YOUR SHIRT SIZE for a free Monster Tower T-Shirt.  International 

customers will need to cover the shipping cost. 

 

Using your Monster Tower – Operating Instructions 

 

The Monster Tower folds down flat to fit under your boat cover fast and easy.  To fold the tower down 

remove the Quick Release bolts from the front bases.  The Heim joints now allow the tower to pivot 

towards the back of the boat.  If the tower rests on fiberglass, use a vest or other cushion to protect the 

boat and tower. 

DO NOT

 loosen the set screws to flatten out the top section. The top section needs to 

stay at the same angle folded as when not folded. The front legs are then folded one at a time to the side 

for storage.  Always use a vest, koozie or other cushion to protect the boat where the leg touches and if 

the two front legs touch each other.  

 

 

 

  Remember to protect your boat and tower when the tower is folded down.  We recommend using 

a koozie, ski vest or other padding between any locations where the tower front legs touch each 

other, or anywhere the tower touches your boat to protect each item.  It is normally a great place 

to hang your vest to dry after riding as well. 

 

  When towing your boat the Monster Tower can be in the up or folded position.  If you tow with the 

tower up, note the height of the tower and make sure you have overhead clearance.  If you tow 

with the tower down make sure you have pads where the tower touches the boat or where the 

front legs touch to prevent damage. 

 

  The Monster Tower is stiff and silent by design.  If you hear any rattling or noise from the tower; 

or see any movement in the tower, then check all hardware for tightness.  Call us at 877-77-

Tower if this does not correct the problem. 

 

-

 

Always understand and follow the warnings on the tower warning label  

 

Summary of Contents for MT1













Reviews: