background image

14 

TECHNICAL SUPPORT 

Monoprice is pleased to provide free, live, online technical support to assist you with any 
questions you may have about installation, setup, troubleshooting, or product 
recommendations. If you ever need assistance with your new product, please come online 
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical 
support is available through the online chat button on our website www.monoprice.com 
during regular business hours, 7 days a week. You can also get assistance through email by 
sending a message to [email protected] 
 

SPECIFICATIONS 

Model 

18513 

Audio Inputs 

Stereo analog RCA 

Audio Outputs 

Buffered stereo analog RCA loop output 

Output Power 

50 watts/channel into 8 ohms with < 0.1% THD+N or  
65 watts/channel into 4 ohms with < 0.1% THD+N or 
120 watts into a single 8-ohm load with < 0.1% THD+N 

Maximum Speaker Wire Size 

12 AWG 

Minimum Output Impedance 

4 ohms in stereo mode 
8 ohms in mono bridged mode 

Trigger Input 

12 VDC, 10 kΩ 

Trigger Output 

12 VDC, 100mA 

Input Power 

100 ~ 240 VAC, 50/60 Hz, 2.5A 

Standby Power Consumption 

≤ 0.5 watts 

Dimensions 

8.5" x 10..5" x 1.8" (216 x 267 x 45 mm) 

 
 

 

Summary of Contents for 18513
















Reviews: