Moni C051, Instruction Manual

Page: 13 / 15

ASSEMBLY STEPS
• WARNING! Adult assembly required.
• Note: Some parts might be factory assembled.
•Care should be taken in unpacking and assembly of the vehicle. Do not allow the children to play with any of the parts or to help in
the assembly of the vehicle. Risk of injury due to small parts, sharp edges and sharp points in the vehicle’s unassembled state.
• Identify all parts before assembly and save all packing material until assembly is complete to ensure that no parts are discarded
• After each step you must check if each part is correctly placed and well fixed. Follow strictly each step and study well the
assembly figures.
• Assembly tools needed: screwdriver (not included in the set) and spanner (not included in the package).
•
DO NOT over-tighten in order to avoid any damage.
1.Mounting the front fork, front wheel and fende r – Slide the front fork through the openings in the fender. Fix it using 2 screws
and nuts. Take the front wheel axle and slide it through the opening on the left side of the fork. Put a washer

slide the axle
through the front wheel

put one washer

slide through the opening on the other side of the fork. Put a washer and a screw on
each side of the fork, which shows out of the fork. Fix using 2 spanners. After that slide the fork through the fender and the opening
in the motorbike body, designated for it.
2.Attaching the handlebar – Take off the screws from the front fork and then attach the fork to the mask. Replace the screws and
tighten them. Attach the decorative dashboard to the top of the front fork. Take out the M8 machine bolt from the motorbike body.
Attach the fork with the mask to the body. Slide the M8 Machine bolt through the openings in the dashboard and the body. Place a
washer at its end. Fix it using M8 nut.
3.Mounting the basket – Remove the screws from the basket holder. Place the holder in the rear of the motorbike body and fix it
using these screws. Attach to the holder the basket and use 3 pcs 4*12 flat head screws to fix the basket.
4.Attaching the seat - Place the seat in the curved part of the motorbike body. Fix it using flat head screw (Ø4Х10).
5.Placing the rearview mirrors – Remove the screws from the front part of the motor. Attach the mirrors and fix them with these
screws.
12
USE OF THE PRODUCT
Notice: When you change the direction of movement, first make sure that the motorbike is not in motion. Otherwise, if you change
the direction of movement suddenly without stopping the motorbike first, the gears and motor may get damaged.
1.Before first use time, connect the cables to the battery terminals. Red cable must be connected to red terminal. Do not connect
red cable with black terminal. Otherwise, you can cause short cut.
2.Charge the battery completely before using the motorbike for the first time. The charging hole is on the backside of the motorbike.
Connect the charger plug to a power outlet and its socket to the motor outlet.
3.Charge the battery for the first time for 8 – 10 hours, but not more than 12 hours.
4.Before charging the battery, you must turn off the motorbike from the power button.
5.After each use, charge the battery for 8 – 12 hours, but not more.
6.When the speed of the motorbike visible is reduced, you should charge the battery.
7.In order to move the motorbike forward: 1.Turn on the power button (ON/ OFF). 2. Put the forward/ backward switch to position
Forward. 3. Push the pedal.
8.In order to move the motorbike backward: 1.Turn on the power button (ON/ OFF). 2. Put the forward/ backward switch to position
Backward. 3. Push the pedal.
9.Before changing the directions forward – backward, the motorbike must not be moving.
10.If you are not using the motorbike, turn off all of the buttons and place them in neutral position.
Do not listen too loud music, because this may lead to impairment of the hearing.
CHARGING OF THE BATTERY OPERATED MOTORBIKE
WARNING!!!
• IN ORDER TO AVOID FIRE AND ELECTRIC SHOCK:
- NEVER USE battery or charger of other brand or another product. Always use only the rechargeable battery and adapter
provided with the bought product.
- Do not use the battery or adapter for another product. This may result in overheating, fire or explosion.
-
NEVER change the electric current. Making any changes to it may lead to short circuit, fire or explosion or the system may
permanently get damaged.
•
Do not allow Your child to charge the battery.
- DO NOT ALLOW DIRECT CONTACT BETWEEN THE TERMINALS OF THE BATTERY. THIS MAY LEAD TO FIRE OR
EXPLOSION.
- During charging keep the battery away from easy flammable items.
- Never pick up the battery by its cable or adapter. This may lead to damaging of the battery resulting in a fire. Pick the
battery by the corpus
ONLY .