Monessen Hearth DLX18 Installation And Operating Instructions Manual Download Page 23

22                                                                                                                                                                                 

14D9999

14D9999                                                                                                                                                                                                    

23

Top Locating 

Pins 

W

ARNING

CAUTION

LOG PLACEMENT

Before you begin 

— This unit is supplied with a set of ceramic fiber logs. Do not handle these logs with your bare hands. 

Always wear gloves to prevent skin irritation from ceramic fibers.

 After handling logs, wash your hands gently with soap 

and water to remove any traces of fibers.

PROPER SEQUENCE OFLOG 
INSTALLATION - 

See Figure 21

1.   Install the

 Rear Log (#1)

 on the top 

set of locating pins. Visually check to 
verify the log is securely placed on the 
pins, and in contact with the grate.

2.   Install the 

Right Longer Front Log 

(#2)

 on top of the piezo and control 

cover.  Center  the  log  left  to  right  to 
properly engage the locator lugs. 

3.   Place the 

Left Shorter Front Log (#3)

 

in  front  of  the 

Right  Longer  Front 

Log (#2)

3.   Install the 

Center Log (#4)

 behind the 

Right Longer Front Log (#2)

 on the 

remaining set of locating pins. Visu-
ally check to verify the log is securely 
placed on the pins.

4.   Install the

 Cross Log (#5)

 by engaging 

the holes in the cross log onto pins on 
the rear log.

PLACING THE DECORATIVE ROCK 

Figure 21 - Proper Sequence of Log Installation 

Rear Log 

#1

The positioning of the logs is critical to the safe and clean operation of this heater. 
Sooting and other problems may result if the logs are not properly and firmly positioned 
in  the  appliance.  Never  add  additional  logs  or  embellishments  such  as  pine  cones, 
vermiculite or rock wool to the heater. Only use the logs supplied with the unit. 
Failure  to  position  the  parts  in  accordance  with  diagrams  below  or  to  use  only 
parts  specifically  approved  for  this  heater  may  result  in  property  damage  or 
personal injury.

W

ARNING

DO NOT sprinkle volcanic rock on the logs or around the pilot or the main burner. This 
may cause sooting. Only place volcanic rock on the floor of the fireplace.
During initial operation of the new heater, burning logs will give off a paper burning 
smell and orange flames will be present. Simply open the windows for a few hours to 
vent the odor. 

CAUTION

Left 

Shorter 

Front Log 

#3

Right 

Longer 

Front Log 

#2

Center Log 

#4

Cross Log 

#5

Locating 

Pins 

Summary of Contents for DLX18





































Reviews: