Monessen Hearth Direct Vent BLDV400 Installation And Operating Instructions Manual Download Page 49

Page: 49 / 68

74D0009

Figure 63 - Pilot Flame

Thermopile

Thermocouple

Sensor

Sparker

BURNER, PILOT AND CONTROL COMPARTMENT

Keep the control compartment, logs, and burner areas surrounding the logs clean

by vacuuming or brushing at least twice a year. Make sure the burner

porting, pilot air opening and burner air opening are free of obstructions

at all times.

PILOT FLAME

The flames from the pilot should be visually checked as soon as the

heater is installed and periodically during normal operation.

The pilot

flame must always be present when the fireplace is in operation.

Figure 63

. The pilot flame has three distinct flames, one engulfing the

thermopile, one engulfing the thermocouple, and the other reaching to

the main burner.

BURNER

Inspect area around the injector. Remove any lint or foreign material

with a brush or vacuum.

Turn off gas before servicing fireplace. It is recommended that a qualified service

technician perform these check-ups at the beginning of each heating season

ARNING

BURNER FLAME

The flames from the burner should be visually

checked as soon as the heater is installed and

periodically during normal operation. In normal

operation, at full rate, and after operating for about

15 to 30 minutes, the flame should be yellow and

slightly taller than the rear log.

Figure 64

If the flame is blue and only in the center, turn off

unit and let cool. After unit is cool, remove logs and

check to make sure the back holes in the burner

are not covered with rock wool. If the back holes

are clear, add more rock wool to the center of the

burner. Replace logs.

NOTE: The type of installation, vent system

configuration, and wind effects may cause the

flame patterns to vary.

Figure 64 - Burner Flame Appearance

CLEANING AND MAINTENANCE

Summary of Contents for Direct Vent BLDV400





































































Search results

Summary of Contents for Direct Vent BLDV400

Reviews:

Related manuals for Direct Vent BLDV400

Brands by name

Popular brands

Monessen Hearth Direct Vent BLDV400, Installation And Operating Instructions Manual

Search results

Summary of Contents for Direct Vent BLDV400

Reviews:

Related manuals for Direct Vent BLDV400

Brands by name

Popular brands