background image

Monarch Zener Owner’s Manual v2.  © Scooters Australia 2017. 

 

18

 

 

 
7. CARE AND MAINTENANCE 

 

ROUTINE MAINTENANCE EVERY TWELVE MONTHS 

To protect your scooter and ensure that it remains in a safe and reliable condition, we strongly 
advise you to have your scooter serviced every 12 months by an authorised dealer. This also 
protects your warranty. Services can be arranged by contacting your nearest dealer and 
organising either a home service or a service in the workshop. Fees may apply for additional time 
taken if you organise a home service. 
 

 
CLEANING YOUR SCOOTER  
Tyres

: Clean the tyres with ordinary kitchen-type cleaners and a damp cloth. Do not use solvents 

on the tyres. Solvents can cause the tyre material to break down or become too soft. 

Body: 

The body (rear shroud, tiller shroud, deck shroud) of your scooter is formed ABS plastic 

and coated with a durable automotive-type finish. Use cool water mixed with a mild soap to 
remove dirt and oils. Use a nonabrasive car wax on the ABS body parts. Buff by hand with a soft 
cloth. Mr Sheen or similar is a good product to use. 

Seats: 

Clean with a mild soap or mild detergent and a damp cloth. A vinyl cleaner may also be 

used. 

Floor mat:

 Wipe over the floor mate with a damp cloth. 

 

 
BATTERIES AND CHARGING 

Battery maintenance is the most important part of maintaining your scooter. 

Keeping the 

batteries fully charged helps to extend battery life.

 Use the following guidelines to help keep 

your batteries in optimum condition. Batteries need about 20 cycles to reach their maximum 
potential. 

  For daily use, keep batteries fully charged. We recommend that you plug in the off-board 

charger at the end of each day the scooter is used and charge overnight for at least 8 
hours. 

  If you are not going to use the scooter for more than a week, fully charge the batteries and 

then disconnect them from the scooter. See Fig. 13. 

 

To Charge the Batteries: 

The charger for is an off-board type of charger. To charge the batteries:  

1. Plug the charger into the charger port on the tiller. See Fig 20. 
2. Plug the charger into the power point 
3. Turn the power point on 
4. Turn the Charger on and leave on until at least 1 hour after the green light has come on. 

 
NOTE: Do not turn the charger off and leave it plugged into the scooter  

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
Battery Maintenance 

Your batteries are a sealed type and cannot leak (see Fig. 21). They are capable of about 300 
discharge cycles. If you discharge them less than fully, they will achieve a higher number of 
cycles. They are maintenance free. 

 

 

Figure 20. 

 
 

Figure 21. 

 
 

Summary of Contents for ZENER


























Reviews: