background image

LIMITED MONARCH INDUSTRIES WARRANTY

For one year from date of purchase, Monarch Industries will replace or repair for the original purchaser, free of
charge, any part or parts, found upon examination by any Monarch Industries Authorized Service Depot or by the
Monarch factory, to be defective in material or workmanship or both. Equipment and accessories not manufac-
tured by Monarch Industries are warranted only to the extent of the original manufacturer's warranty. All transpor-
tation charges on parts submitted for replacement or repair under this warranty must be borne by the purchaser.
For warranty service see your nearest Monarch Industries Authorized Service Depot. THERE  IS  NO  OTHER
EXPRESS WARRANTY.  IMPLIED  WARRANTIES  INCLUDING  THOSE  OF  MERCHANTABILITY  AND
FITNESS  FOR  A PARTICULAR  PURPOSE  ARE  LIMITED  TO  ONE  YEAR  FROM  PURCHASE  AND  TO
THE  EXTENT  PERMITTED BY  LAW.   LIABILITY  FOR  CONSEQUENTIAL  DAMAGES  UNDER  ANY  AND
ALL  WARRANTIES  ARE EXCLUDED  TO  THE  EXTENT  EXCLUSION  IS  PERMITTED  BY  LAW.
This warranty is an addition to any statutory warranty.

TROUBLES SHOOTING GUIDE

a)

Motor will not start:

1)

No power due to blown fuses, open switches or loose connec-
tions.

b)

Pump fails to deliver water:

1)

Pump not completely primed.

2)

Suction lift is too great.

3)

Foot valve is either not submerged, buried in the mud or
plugged.

c)

Pump losses prime:

1)

Air leaks in suction line.

2)

Well draw down too far.

3)

Faulty foot valve.

d)

Pump delivers water but not at rated capacity:

1)

Leaks in suction or discharge line.

2)

Foot valve, suction line, impeller or nozzle are partially
plugged.

3)

Suction lift is greater than recommended.

4)

Improper impeller rotation or low speed.

5)

Motor does not come off starting windings.

6)

Low line voltage at motor.

1-800-PUMPBIZ 
    PumpBiz.com

Summary of Contents for MJSE

Page 1: ...y by the amount of water needed and the length of the pipe The pipe selected should be large enough so that the friction loss determined fromTable 2 Friction Loss Chart will never exceed a 20 ft 6m head APPLICATION This jet sprinkler pump is a versitile pump for pressure boosting small underground sprinkler systems operating lawn sprinklers and a multitude of other general purpose applications Thi...

Page 2: ...8 3 10 1 46 43 16 48 6 15 1 3 96 1 87 55 18 60 5 18 7 4 93 2 33 69 20 73 5 22 8 6 00 2 83 84 Loss of head in meters due to friction per 100 meters of pipe Nominal Pipe Size 20mm 25mm 32mm 40mm 50mm L Min 15 3 7 1 15 0 30 0 13 20 5 3 1 64 0 43 0 19 25 7 1 2 18 0 56 0 27 30 13 5 4 13 1 08 0 49 35 16 3 5 00 1 31 0 61 40 23 5 7 30 1 90 0 88 0 25 45 28 3 8 74 2 31 1 07 0 29 50 34 2 10 6 2 79 1 32 0 38 ...

Page 3: ...e turned by hand insert a flat object into the impeller vane 7 Slip the rotating seal 7 off the shaft and remove the seal plate 8 8 Remove the ceramic seal seat 9 from the seal plate Fig 2 Reassembly 1 Clean all the parts thoroughly before assembling 2 Push ceramic seal 9 it into the seal plate using thumbs only Make sure the smooth surface of the ceramic seat faces outwards 3 Put the seal plate b...

Page 4: ...FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR FROM PURCHASE AND TO THE EXTENT PERMITTED BY LAW LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW This warranty is an addition to any statutory warranty TROUBLES SHOOTING GUIDE a Motor will not start 1 No power due to blown fuses open switches or loose connec tions b Pump fails...

Reviews: