molex 57022 Series Operating Manual Download Page 3

A–1 

<Safety Precautions>

 

Please read the following before operating the tool. 

 
 

 

 

1. Introduction

 

 

Thank you for choosing our Hand Crimp Tool. 
This document is prepared so that the tool is properly used.   

Please take the time to read this manual, making sure you understand the operating 
procedures described herein before attempting to operate the tool. 

 

 
 

2. Dangerous operations

 

 
1)  Don’t insert a part of your body or other foreign materials in the hand crimp tool 

(hereinafter referred to as the “tool”) while you’re operating the handle of a tool, as injury 

my result. 

 

2)  Beware of a handle when it is opened. Releasing a ratchet may cause the handle to open 

abruptly, resulting in injury. 

 

3)  Only users who have received adequate training on usage and safety from their manager, 

and have appropriate knowledge and skills must use the tool. Use by unfamiliar users may 
cause injury. 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

<Caution> 

1)  Unauthorized reproduction of this document in part or in whole is prohibited. 
2)  The contents of this document are subject to change without notice. 
3)  Molex Japan Co., Ltd. assumes no responsibility for losses resulting from use or

misuse of this document. 

Summary of Contents for 57022 Series













Reviews: