4
D
E
Inspect current mounting ring seals, your new diposal may
be compatible with the existing mounting ring and could
be reused. If the existing sink flange is to be reused, go to
page 6. If unable to be used, remove the old sink flange
from the sink. Clean the sink thoroughly.
Inspect current mounting ring seals, your new diposal may
be compatible with the existing mounting ring and could
be reused. If the existing sink flange is to be reused, go to
page 6. If unable to be used, remove the old sink flange
from the sink. Clean the sink thoroughly.
Inspect current mounting ring seals, your new diposal may
be compatible with the existing mounting ring and could
be reused. If the existing sink flange is to be reused, go to
page 6. If unable to be used, remove the old sink flange
from the sink. Clean the sink thoroughly.
HELPFUL HINT: Unless you have a new home, this is a good time to clean out the trap and drain lines by running a drain auger or plumber’s
snake before installing your new disposal.
HELPFUL HINT: Unless you have a new home, this is a good time to clean out the trap and drain lines by running a drain auger or plumber’s
snake before installing your new disposal.
HELPFUL HINT: Unless you have a new home, this is a good time to clean out the trap and drain lines by running a drain auger or plumber’s
snake before installing your new disposal.
REMOVAL OF OLD DISPOSAL
TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY.
Disclaimer: If there is no disposal, skip to page 5.
REMOVAL OF OLD DISPOSAL
TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY.
Disclaimer: If there is no disposal, skip to page 5.
REMOVAL OF OLD DISPOSAL
TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY.
Disclaimer: If there is no disposal, skip to page 5.
HARDWIRE REMOVAL
HARDWIRE REMOVAL
HARDWIRE REMOVAL
Turn off power. When the disposal is removed from sink flange, disconnect any hardwired connections or unplug unit.
NOTE:
Your Moen Disposal requires an electrical outlet to plug into. You do not need to hardwire connection to disposal.
Disclaimer:
If you are not familiar with electrical power and procedures, call a qualified electrician.
A.
Connect the disposal cord to 110-120 volt, 60 Hz AC current only.
B.
This waste disposal is equipped with a factory installed plug-in cord with a three prong grounding plug. If a 110-120
volt, 60 Hz AC grounding outlet is not available, have a proper outlet installed by a qualified electrician.
C.
This waste disposal requires that a dedicated switch with a marked “Off“ position. The switch shall be installed within sight
of the sink opening or the disposal.
Turn off power. When the disposal is removed from sink flange, disconnect any hardwired connections or unplug unit.
NOTE:
Your Moen Disposal requires an electrical outlet to plug into. You do not need to hardwire connection to disposal.
Disclaimer: If you are not familiar with electrical power and procedures, call a qualified electrician.
A.
Connect the disposal cord to 110-120 volt, 60 Hz AC current only.
B.
This waste disposal is equipped with a factory installed plug-in cord with a three prong grounding plug. If a 110-120
volt, 60 Hz AC grounding outlet is not available, have a proper outlet installed by a qualified electrician.
C.
This waste disposal requires that a dedicated switch with a marked “Off“ position. The switch shall be installed within sight
of the sink opening or the disposal.
Turn off power. When the disposal is removed from sink flange, disconnect any hardwired connections or unplug unit.
NOTE:
Your Moen Disposal requires an electrical outlet to plug into. You do not need to hardwire connection to disposal.
Disclaimer: If you are not familiar with electrical power and procedures, call a qualified electrician.
A.
Connect the disposal cord to 110-120 volt, 60 Hz AC current only.
B.
This waste disposal is equipped with a factory installed plug-in cord with a three prong grounding plug. If a 110-120
volt, 60 Hz AC grounding outlet is not available, have a proper outlet installed by a qualified electrician.
C.
This waste disposal requires that a dedicated switch with a marked “Off“ position. The switch shall be installed within sight
of the sink opening or the disposal.
