3
INS972D - 12/13
2"-2 7/8"
(50-73mm)
Use 1/2” Copper or
IPS Pipe Only
Use tubo de cobre de 1.27 cm
o tubería IPS solamente
Utiliser un tuyau en cuivre ou
IPS de 1/2 po seulement
78"
(1420mm)
32"
(970mm)
6"min-11"max
(153-279mm)
1
3-3/4" (95mm)
K
For ease of operation and best performance, install the valve body 32” above the
floor and the shower arm at 78” above the floor. The tub spout can be installed be-
tween 6” and 11” below the valve body using ½” copper tubing or the equivalent to
½” iron pipe size material. No more than one elbow is recommended.
If your supply lines are coming up to the valve from below, follow Step 1, then skip
to step 5. If your supply lines are coming down to the valve from above, follow Step
1 Optional, then step 1A – 4A
For ease of operation and best performance, install the valve body 32” above the
floor and the shower arm at 78” above the floor. The tub spout can be installed be-
tween 6” and 11” below the valve body using ½” copper tubing or the equivalent to
½” iron pipe size material. No more than one elbow is recommended.
If your supply lines are coming up to the valve from below, follow Step 1, then skip
to step 5. If your supply lines are coming down to the valve from above, follow Step
1 Optional, then step 1A – 4A
For ease of operation and best performance, install the valve body 32” above the
floor and the shower arm at 78” above the floor. The tub spout can be installed be-
tween 6” and 11” below the valve body using ½” copper tubing or the equivalent to
½” iron pipe size material. No more than one elbow is recommended.
If your supply lines are coming up to the valve from below, follow Step 1, then skip
to step 5. If your supply lines are coming down to the valve from above, follow Step
1 Optional, then step 1A – 4A
This valve (E) can be plumbed using threaded connections (IPS). The water
inlets, the outlets to the tub spout and to the showerhead are ½” male pipe
thread. Use thread seal tape when making these connections. Wrap the tape
onto the threads in the same direction the adapter will thread on. Go to step 5.
This valve (E) can be plumbed using threaded connections (IPS). The water
inlets, the outlets to the tub spout and to the showerhead are ½” male pipe
thread. Use thread seal tape when making these connections. Wrap the tape
onto the threads in the same direction the adapter will thread on. Go to step 5.
This valve (E) can be plumbed using threaded connections (IPS). The water
inlets, the outlets to the tub spout and to the showerhead are ½” male pipe
thread. Use thread seal tape when making these connections. Wrap the tape
onto the threads in the same direction the adapter will thread on. Go to step 5.
If soldering copper tubing (CC) into valve (E) insert ½” copper tubing into
the hot and cold water inlets and the shower riser and tub drop outlets.
Then, go to step 5
If soldering copper tubing (CC) into valve (E) insert ½” copper tubing into
the hot and cold water inlets and the shower riser and tub drop outlets.
Then, go to step 5
If soldering copper tubing (CC) into valve (E) insert ½” copper tubing into
the hot and cold water inlets and the shower riser and tub drop outlets.
Then, go to step 5
1
IPS
Thread seal tape
Cinta para sellar roscas
Ruban pour joints filetés
E
5
GO TO
VAYA AL PASO
ALLER À L'ÉTAPE
CC
Optional/Optionnel/Opcional
E
1
5
GO TO
VAYA AL PASO
ALLER À L'ÉTAPE
or
o
ou
