background image

2

3

Important Safety Information

WARNING – AS WITH ALL ELECTRICAL PRODUCTS

, care and general precautions must 

be observed in order to operate this equipment safely. If you are unsure how to operate this 
apparatus in a safe manner, please seek appropriate advice on its safe use.

ENSURE CORRECT BATTERY POLARITY - FAILURE TO INSTALL BATTERIES CORRECTLY 
MAY CAUSE PERMANENT DAMAGE

This apparatus 

MUST NOT BE OPERATED NEAR WATER

 or where there is risk of the 

apparatus coming into contact with sources of water such as sinks, taps, showers or outdoor 
water units, or wet environments such as in the rain. Take care to ensure that no liquids are 
spilt onto or come into contact with the apparatus. In the event this should happen remove 
power from the unit immediately and seek expert assistance. 

This apparatus produces sound that could cause permanent damage to hearing. Always 
operate the apparatus at safe listening volumes and ensure you take regular breaks from 
being exposed to sound levels 

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS APPARATUS

. It should only be 

serviced by qualified service personnel, specifically when: 

• 

The apparatus has been dropped or damaged in any way or anything has fallen on the 
apparatus 

• 

The apparatus has been exposed to liquid whether this has entered the apparatus or not 

• 

The power supply cables to the apparatus have been damaged in anyway whatsoever 

• 

The apparatus functions in an abnormal manner or appears to operate differently in any 

• 

way whatsoever. 

Summary of Contents for SKULPTsynthesiser


























Reviews: