background image

3)  Locate the battery clip.  Cut 1 ½” length off the ends of each 
lead and discard (or save for other projects).  Connect the black 
lead to the “ring” lug of the input jack.  Connect the red lead to 
terminal #2 of the terminal strip.  Solder these connections now.

SECTION 4 – Wire Remaining Connections 

1)  Strip and tin a 1 ½” piece of wire and connect footswitch lugs “3” and “9”.

2)  Strip and tin a 1" piece of wire and connect the input jack “tip” lug to the footswitch lug “2”.

3)  Strip and tin a 3 ½” piece of wire and connect footswitch lug “1” to distortion pot lug “1”.

4)  Strip and tin a 1 ¾” piece of wire and connect the output jack “ground” lug to 
output pot lug “3”.

GROUND LUG

TIP LUG

5)  Strip and tin a 1 ¼” piece of wire and connect the output jack “tip” lug to 
footswitch lug “8”.

6)  Strip and tin a 2 ½” piece of wire and connect the output pot lug “2” to footswitch lug “7”.

Finish it off by double-checking all of your connections, connect and insert a 9V battery, screw the lid on and 
fasten the knobs to both pot shafts.

RING LUG

SLEEVE LUG

TIP LUG

8

7)  Strip and tin a 2 ½” piece of wire and connect the cathode lead of the LED to footswitch lug “4”.  
Solder both of these connections now.

8)  Strip and tin a 1 ½” piece of wire and connect the footswitch lug “5” to the ground lug of the input 
jack.  Solder these connections now.

SECTION 3 – Mount and Connect Remaining Components 

1)  Connect one of the 0.1

µ

F capacitors with one lead at terminal #5 of the terminal strip and the 

other lead to output pot lug “1”.

2)  Connect the other 0.1

µ

F capacitor to terminal #4 and to both lugs “2” and “3” of the distortion pot.  

Solder all connections at terminals #3, #4 and distortion pot lugs “2” and “3” now.

Please refer to DRAWING 4.

9)  Strip and tin a 1” piece of wire and connect the DPDT switch middle left lug to the output pot’s lug 
“1”.  Solder these connections now.

Summary of Contents for K-956












Reviews: