manualshive.com logo in svg

Mobistat TITAN, User Manual, Page: 13 / 16

Share
Download
Mobistat TITAN User Manual Download Page 13

 

MOBISAT

®

 TITAN - User Manual v.2.0.3 - www.mobisat.eu - Page 13 of 16 

 

DIGITAL OUTPUTS 

The DOUT1 DOUT2 digital outputs can be used to switch electronic devices on and off by remote. 
The digital outputs (e.g. when they are not controlled by the Immobilizer scenario), can be enabled and disabled by sending the 
following command: 

<space> <space>

setdigout

<space>

## 

 

▪

 

The two hashtags can assume the values: 0 (OFF) or 1 (ON). 

▪

 

The first hashtag is digital output 1 (DOUT1) 

▪

 

The second hashtag is digital output 2 (DOUT2) 

 
For example, if the starter block function is installed, the vehicle's starter can be disabled by sending the command: 

<space><space>

setdigout

<space>

01 

In order to start the vehicle, the following command must be sent: 

<space><space>

setdigout

<space>

00

 

 

IMMOBILIZER 

The vehicle can be started only if an iButton

®

 is connected. By connecting DOUT2 to the starter, the use of the vehicle can be 

protected from drivers without an iButton

®

. 

 
N.B.  

▪

 

The DOUT2 output controls this scenario 

▪

 

DIN1 must be installed in order for the Immobilizer to function correctly 

 
DOUT2 is always OFF.  
The status changes to ON when the vehicle is started (DIN1 = 1).  
When any iButton

®

 code is read from the device, the DOUT2 status switches to OFF.  

After identifying the iButton

®

, DIN1 will switch to OFF, making it possible to start the vehicle for 30 seconds, after which the 

iButton

® 

must be identified once again. 

 
TO START THE VEHICLE:  

1.

 

turn on the ignition with the key 

2.

 

connect the iButton

® 

 

3.

 

start up the vehicle with the ignition key. 

 
CAUTION 

▪

 

If the iButton

®

 is not entered within 30s of the dashboard being powered on, the motor will remain blocked (for 30 

seconds) and the identification procedure will need to be repeated 

▪

 

iButtons

®

 should be kept separately from the vehicle's keys (in order to offer greater protection in case of theft 

 

N.B.if the iButton

®

 is lost, the car will remain blocked and the only way to unlock it is to disable the "Immobilizer" scenario (an 

SMS command).  
 
IMMOBILIZER SCENARIO COMMANDS 
 
ENABLE THE IMMOBILIZER SCENARIO: 

<space><space>setparam<space>1601<space>2  

DISABLE THE IMMOBILIZER SCENARIO: 

<space><space>setparam<space>1601<space>0

 

 
 
 

 

Summary of Contents for TITAN

















Reviews:

No comments