MMP NO-HAMMER Assembly Instructions Manual Download Page 7

Page: 7 / 10

PAGE 7 OF 10

TOOLS NEEDED

SCREWDRIVER (FLAT BLADE)

" AND

1
2

" WRENCHES, OR ADJUSTABLE WRENCHES, OR SOCKET SET WITH RATCHET

A PAIR OF RUGGED WORK GLOVES
A PAIR OF SAFETY GLASSES

NO-HAMMER WOODEN FRAME INSTALLATION

STEP 1

STEP 2*

* PLEASE NOTE SOME FRAMING MEMBERS NOT SHOWN FOR VISUAL CLARITY
** FOR DETAILED INSTRUCTIONS REGARDING BUILDING A WOODEN FRAME, PLEASE VISIT OUR WEBSITE AT

WWW.MITCHELLWREATHRINGS.COM

REV: 05

REMOVE THE OUTSIDE FOOT PEDAL BRACKET
FROM FOOT PEDAL ASSEMBLY BY REMOVING THE

INSTALLED

" HEX BOLT & NUT SHOWN IN

DIAGRAM TO THE LEFT
1.

REMOVE THE TWO

1
4

" HEX BOLTS, WASHERS

& NUTS FROM THE OUTSIDE FOOT PEDAL
BRACKET AND BACK UP PLATE

TO MOUNT THE FOOT PEDAL ASSEMBLY TO THE FRAME:

PLACE THE OUTSIDE FOOT PEDAL BRACKET AND BACKUP
PLATE IN THE ORIENTATION SHOWN IN THE DIAGRAM

REPLACE THE TWO

1
4

" HEX BOLTS, WASHERS & NUTS

GOING THRU THE PRE-DRILLED HOLES OF THE METAL
FRAME**

TIGHTEN THE INSTALLED BOLTS

Summary of Contents for NO-HAMMER











Search results

Summary of Contents for NO-HAMMER

Reviews:

Related manuals for NO-HAMMER

Brands by name

Popular brands

MMP NO-HAMMER, Assembly Instructions Manual

Search results

Summary of Contents for NO-HAMMER

Reviews:

Related manuals for NO-HAMMER

Brands by name

Popular brands