WARNING
• The LED Flex is provided with self-adhesive backing - ensure the surface application is clean and
dust free before installation
• Ensuring correct polarity is observed, connect the 230V mains supply to the primary side of the
24V constant voltage driver, Live (brown), Neutral (blue)
• From the secondary side of the driver connect a red and black cable to the input side of the RGB
controller ensuring correct polarity is observed (+ Red) (- Black) (see Fig 2)
Terminate cables from the RGB strip to the RGB controller (black to V+) (red to R) (green to G)
(blue to B) (See Fig 2)
• Switch on power and test for correct operation
LIGHT CONNECTION
The maximum distance that can be run is 10m for 24V LED flex when connected in series (see
Fig 3). To power additional LED flex (depending on LED driver capacity) it is recommended that a
signal amplifier is used to avoid volt drop and increase signal strength. This should be connected
in parallel up to the maximum power of the LED driver and dependent on the RGB controller being
used.
This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
3
LEDF24RGB
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
LEDF24RGB
SAFETY
•
Installation of this product should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•
Please isolate mains prior to installation/maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation
•
This product is Class III
•
This product is IP20 rated
•
This product is fully controllable when used with LEDFR4 or LEDFR5 RGB controller
INSTALLATION
•
Provide power to the point of installation
•
Decide on the desired layout of the LED Flex, taking into consideration the following:
o
The cables are long enough to connect to the driver
o
The LED Flex is not going to be installed in a position where it is at risk of being cut, trapped or
damaged
o
The total maximum length does not exceed the max power rating of the LED driver (see website for
more details)
•
When cutting the LED Flex, ensure it is only cut between the copper connections, approximately every 166mm
along the strips’ length. It is important to only cut along the line indicated between the copper connections (see
Fig 1)
Fig 1
•
The LED Flex is provided with self-adhesive backing, ensure the surface application is clean and dust free before
installation
•
Ensuring correct polarity is observed, connect the 230V mains supply to the primary side of the 24V constant
voltage driver, Live (brown), Neutral (blue)
•
From the secondary side of the driver connect a red and black cable to the input side of the RGB controller
ensuring correct polarity is observed (+ Red) (- Black) (see Fig 2)
Terminate cables from the RGB strip to the RGB controller (black to V+) (red to R) (green to G) (blue to B) (See Fig
2)
RGB Controller
Inp
ut
+
-
V+
R
G
B
LEDF24RGB
Light Connection
The maximum distance that can be run is 20m for 24V LED flex when connected in series (see Fig 3).
To power addition LED flex (depending on LED driver capacity) it is recommended that a signal
amplifier is used to avoid volt drop and increase signal strength. This should be connected in parallel
up to the maximum power of the LED driver and dependent on the RGB controller being used.
Fig 3
LEDF24RGBW
Light Connection
The maximum distance that can be run is 20m for 24V LED flex when connected in series (see Fig 3).
To power addition LED flex (depending on LED driver capacity) it is recommended that a signal
amplifier is used to avoid volt drop and increase signal strength. This should be connected in parallel
up to the maximum power of the LED driver and dependent on the RGBW controller being used.
Fig 2
Fig 3
• Wiring diagram as reference only, driver may differ
10m Max
10m Max
10m Max
