background image

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or 
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class D to Regulation (EU) No. 
2019/2015 and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source and non-replaceable control gear. 
  

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which 
may damage the product.
Please be aware that these products may require an MCB upgrade to a Type C due to high 
inrush currents.
The maximum constant ambient temperature at the point of installation should not exceed 
50

0

C.

This product is dimmable via a 0-10V dimmer, please check compatibility before installation.
This product is DALI compatible. Relevant DALI software and control gear is required for use 
of this functionality. 
This product should be dismantled for disposal when it reaches the end of its life. Please 
see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. 
Check local authorities for where facilities exist. 

WARNING 

This product must be disconnected from the circuit if subjected t
testing. Irreparable damage will occur if this instruction is not fol

GENERAL 

This product contains a light source of energy efficiency class D t

2021 No. 1095.

 

This product contains a non-replaceable LED light source and no

Clean with a soft dry cloth only, do not use aggressive cleaning p

product. 

Please be aware that these products may require an MCB upgrad

The maximum constant ambient temperature at the point of inst

This product is dimmable via a 0-10V dimmer, please check comp

This product is DALI compatible. Relevant DALI software and con

functionality.  

 

This product should be dismantled for disposal when it reaches t
dismantling instructions. 

This product must be disconnected from the circuit if subjected t
testing. Irreparable damage will occur if this instruction is not fol

This product contains a light source of energy efficiency class D t

This product contains a non-replaceable LED light source and no

Clean with a soft dry cloth only, do not use aggressive cleaning p

Please be aware that these products may require an MCB upgrad

The maximum constant ambient temperature at the point of inst

This product is dimmable via a 0-10V dimmer, please check comp

This product is DALI compatible. Relevant DALI software and con

This product should be dismantled for disposal when it reaches t

Summary of Contents for AX CCT











Reviews: