Fig. 3
Note: To change the settings on the optional AXSMOD microwave sensor module, the AXREMC remote
controller is required. The maximum mounting height with the sensor fitted is 15 metres.
Use of the optional AXDMOD module enables the luminaire to become DALI compatible. Relevant DALI
software and control gear is required for use of this functionality.
AXREMC remote control programmer
Insert 2 x AA batteries (not included)
Adjust sensor settings as required (see Fig. 4)
The sensor remote has a maximum range of 15m
BUTTON
FUNCTION
Press to switch between permanent on
and permanent off. To quit this mode
press “AUTO”
Press to switch to sensor mode. All
parameters revert to those last selected
Press to illuminate the current
parameters selected on the remote
Press to upload the selected parameters
to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or
save/confirm the selected mode
Reset to default settings: Brightness
100%, Sensitivity 100%, Hold time
5m, Daylight sensor disabled, Standby
dimming 30%, Standby dimming time
60m
AXREMC REMOTE CONTROL PROGRAMMER
• Insert 2 x AA batteries (not included)
• Adjust sensor settings as required (see Fig. 4)
• The sensor remote has a maximum range of 15m
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit thi
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sele
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illumi
for 2 seconds when motion is detected. The standby period and daylig
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming select
parameters
Daylight sensor mode. When the ambient light level exceeds the set lu
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumina
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parame
press a mode button followed by “OK” to save the settings to that m
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit thi
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sele
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illumi
for 2 seconds when motion is detected. The standby period and daylig
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming select
parameters
Daylight sensor mode. When the ambient light level exceeds the set lu
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumina
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parame
press a mode button followed by “OK” to save the settings to that m
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit thi
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sele
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illumi
for 2 seconds when motion is detected. The standby period and daylig
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming select
parameters
Daylight sensor mode. When the ambient light level exceeds the set lu
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumina
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parame
press a mode button followed by “OK” to save the settings to that m
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit thi
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sele
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold time
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illumi
for 2 seconds when motion is detected. The standby period and daylig
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming select
parameters
Daylight sensor mode. When the ambient light level exceeds the set lu
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumina
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parame
press a mode button followed by “OK” to save the settings to that m
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit th
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sel
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold tim
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illum
for 2 seconds when motion is detected. The standby period and dayli
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming sele
parameters
Daylight sensor mode. When the ambient light level exceeds the set l
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumin
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired param
press a mode button followed by “OK” to save the settings to that
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit th
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sel
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold tim
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illum
for 2 seconds when motion is detected. The standby period and dayli
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming sele
parameters
Daylight sensor mode. When the ambient light level exceeds the set l
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumin
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired param
press a mode button followed by “OK” to save the settings to that
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit th
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sel
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold tim
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illum
for 2 seconds when motion is detected. The standby period and dayli
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming sele
parameters
Daylight sensor mode. When the ambient light level exceeds the set l
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumin
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired param
press a mode button followed by “OK” to save the settings to that
N
O
I
T
C
N
U
F
N
O
T
T
U
B
Press to switch between permanent on and permanent off. To quit thi
mode press “AUTO”
Press to switch to sensor mode. All parameters revert to those last sele
Press to illuminate the current parameters selected on the remote
Press to upload the selected parameters to the sensor
Navigate up and down
Navigate left and right
Confirm the selected parameters or save/confirm the selected mode
Reset to default settings: Brightness 100%, Sensitivity 100%, Hold tim
Daylight mode, Standby dimming 30%, Standby dimming time 60m
Press to check the sensitivity settings are correct. The fitting will illumi
for 2 seconds when motion is detected. The standby period and daylig
sensor are disabled. Press “AUTO” to quit this mode
The sensor will automatically go into test mode after confirming select
parameters
Daylight sensor mode. When the ambient light level exceeds the set lu
level, the luminaire will monitor for 1 minute to confirm the light level
increase is not temporary, and then turn off even when motion is detected.
When the ambient light level drops below the set lux level, the lumina
turn on even without motion detection after 1 minute. This feature is
disabled by default - press to activate and press again to deactivate
Four different modes can be saved. After selecting the desired parame
press a mode button followed by “OK” to save the settings to that m
Fig. 4
When the ambient light level drops below the set lux level, the lumina
When the ambient light level drops below the set lux level, the lumina
When the ambient light level drops below the set lux level, the lumina
When the ambient light level drops below the set lux level, the lumina
When the ambient light level drops below the set lux level, the lumin
When the ambient light level drops below the set lux level, the lumin
When the ambient light level drops below the set lux level, the lumin
When the ambient light level drops below the set lux level, the lumina
