manualshive.com logo in svg

MKS Newport CONEX-LDS, Manual

Share
Download
MKS Newport CONEX-LDS Manual Download Page 23

CONEX-LDS 

Controller GUI Manual 

 

Choosing “Yes” will save the parameters in memory and “No” will cancel the 

operation. 

Set Volatile 

Writes to volatile memory and is lost upon reboot. 

4.6.2

 

Dark current calibration 

Update Button 

Updates the offsets. Follow the pop up messages to complete the process. 

 

 

NOTE 

This function minimizes the effects of internal reflections that reach the sensor 

and impact the measurement signal. The laser should be ON for a least 10 

minutes before performing this calibration. A non-reflective shutter should be 

inserted as close as possible to the autocollimator beam output.  
This calibration is performed on each CONEX-LDS at the factory and can be 

performed on site. Be familiar with the process before attempting to proceed, 

since it could be source of measurement errors, if not properly done. 

4.6.3

 

Low pass filter 

Set volatile Button 

Applies the new value of the low pass filter frequency. 

Set permanent Button 

Saves the new value of the low pass filter frequency in the memory of the CONEX-

LDS. The controller will need to b in Configuration state, in order for the changes to 

take place. 

 

19 

EDH0331En1032 — 12/18

 

Summary of Contents for Newport CONEX-LDS





























Reviews:

No comments

Brands by name

Popular brands

Load more brands