MK Diamond Products MK-101 PRO24, Owner'S Manual

Page: 19 / 68

19
The warning labels contain important safety information. Please read the information contained on
each safety label. These labels are considered a permanent part of your saw. If a label comes off or
becomes hard to read, contact MK Diamond or your dealer for a replacement.
SAFETY LABEL LOCATIONS
MK-101 Pro24 JCS SAFETY
Part # 164202
A
B
C
D
E
F G
WARNING
• This equipment may produce dust or mists containing
crystalline silica.
• Silica is a basic component of masonry, concrete, and
other materials.
• Repeated and/or substantial inhalation can cause
serious or fatal respiratory diseases including silicosis.
• Respirable crystalline silica is listed by California and
other authorities as a substance known to cause cancer.
• Employ dust controls and protection per
OSHA/NIOSH/MSHA.
!
Part # 155806
• For Your Own Safety Read Instruction
Manual Before Operating Saw.
• Wear Eye Protection.
• Disconnect Saw Before Servicing, when
Changing Cutting Wheels and Cleaning.
• Use Tool Only with Smooth Edge Cutting
Wheels Free of Openings and Grooves.
• Replace Damaged Cutting Wheel Before
Operating.
• Do Not Fill Water Bath Above Water Fill Line.
• See Manual for Pump Replacement.
!
WARNING
Part # 154822
Receptacle is for water
pump only.
125V .6 amps max.
! CAUTION
Part # 155678
! CAUTION
This saw is to be used
with a Ground Fault
Circuit Interrupter.
Part # 155038
SERVICE OR
WARRANTY
FOR INFORMATION ON
PLEASE CALL
1-800-474-5594
Part # 155672
NOTICE
Most motor problems are caused by
low voltage from improper extension
cords. See owner’s manual for
extension cord selection.
!
Part # 170480
Scan for manuals
WARNING
!
Read and understand all instructions.
Failure to follow all instructions in sequence
could result in serious injury.
Maximum material load 35 lbs. (15.9kg)
Place unit on a hard level surface.
DO NOT use as ladder or scaffolding.
Always use with Safety Arm in place.
A
F
Z
D
C
B
Fig 1 Fig 2
Fig 4
Fig 5
H
X
X
B
H
Y
Z
G
F
G
C
D
Locations of
Operating Features
Read Owner’s Manual for
complete Instructions
U.S. Patent No. 7,419,538
Left Hand
Side
Set Up Instructions:
1. (Fig 1) Pull & turn Pin A to lock wheel.
2. (Fig 2 & 3) Stand on left hand side of saw. Pull Blue Knob B &
pull front legs out from H slowly.
3. Grab Handle X with left hand & place left foot on Wheel Y. (Fig 4)
Tilt Saw & rest front legs on ground.
4. (Fig 4 & 5) Foot on Cross Bar F & lift Handle G vertically.
5. (Fig 5) Pull Green Knob C to release safety arm D.
6. Ensure Safety Arm D rests on stand.
Take Down Instructions:
1. Pull table toward operator.
2. (Fig 5) Pull Green Knob C & swing Safety Arm D up. Release
Green Knob C to secure Safety Arm D.
3. (Fig 5 & 4) Push down on Handle G to collapse tile saw.
4. (Fig 3) Hold Saw from handle X & tilt saw to upright position.
5. (Fig 3) Hold up front legs & flip Red Safety Latch Z to unlock
front legs.
6. (Fig 2) Push front legs against frame to lock in place with Blue
Knob B.
7. (Fig 1) Pull back Pin A & place behind retaining rod to keep
wheel unlock.
Fig 3
Label Part # 162083
Part # 162083
H
H
A
C
D
B
E
F
G
Decal/Label Location Description
A Motor - Front Warning - Silica Warning
B Motor - Front Warning - Read and Follow Operating Instructions
C Motor - Back Caution - Receptacle for Water Pump
D Motor - Back Caution - Use with GFCI only
E Motor - Side Service/ Warranty
F Motor - Side Notice - Voltage/extension cords
G Motor - Front QR Codes for Manuals
H Stand Read Manual - Instructions for the stand