background image

CHAPTER 11 

OPTIONAL EQUIPMENT 

 

 

 

 

39 

11.1 

GENERAL 

 

Although all the exterior equipment on your boat was selected with marine service in mind, it is 
helpful to rinse the boat with freshwater after exposure to saltwater. 

 

11.2 

ANCHOR WINDLASS  

(Optional) 

 

Refer to the manual that came with your windlass for specific operating instructions. 
 
The windlass draws lots of power from the house bank.  It’s advisable to only use the windlass 
when  the  engine  is  running,  and  to  allow  time  for  the  battery  to  recharge  after  windlass  use. 
Never try to move the boat forward with the windlass- it is sized to retrieve the anchoring gear, 
not  to  pull  the  boat  forward.  If  the  windlass  bogs  down,  use  the  boat’s  engine  to  move  directly 
over  the  anchor.  If  the  anchor  has  become  firmly  lodged,  use  the  boat’s  engine  to  free  it,  then 
commence  retrieval  with  the  windlass.  Note:  always  let  the  windlass  come  to  a  stop  before 
reversing direction; otherwise, the windlass fuse/breaker may blow.  
 
To use the windlass, the engine start battery switch and house battery switch must both be ON 
and the windlass breaker on the panel must be ON.  
 
If  the  windlass  is  allowing  the  chain  or  rode  to  slip,  tighten  the  break  with  the  windlass  handle 
provided by inserting it into the socket on top. 

 

To avoid chafe on the anchor rode when anchoring, it is advisable to remove the 

rode  from  the  anchor  roller  by  grabbing  it  below  the  roller,  then  pulling  it  up  directly  from  the 
anchor,  feeding  it  through  a  bow  chock  to  a  mooring  cleat.  Never  rely  on  the  windlass  itself  to 
hold the anchor rode- a chain stopper or a cleat should be used to take the load so as to avoid 
damaging the windlass’ gears or having it run out unexpectedly. 
 

 

When  not  using  the  windlass  or  when  underway,  we  recommend  securing  the 

anchor  and  chain  with  a  spare  fender  warp  to  one  of  the  mooring  cleats.    This  prevents  the 
anchor and rode from inadvertently running free underway and fouling the prop. 
 

Anchor Washer

    By holding down the switch on the console for the Anchor Washer, when the 

Fresh Water breaker on the DC Panel is ON, you are able wash the anchor rode and chain with a 
spray of fresh water as it is being retrieved.  The anchor washer is a spray nozzle located on the 
stem of the boat under the anchor roller. 

 

11.3 

PILOTHOUSE CURTAINS 

 

There  are  3  options  with  aft  curtains  (1)  the  most  common  is  to  roll  up  the  center  section  with 
screen/window and secure with 2 straps, leaving the side aft curtains in place. (2) roll up all 3 aft 
curtains by keeping all 3 zipped together and rolled up as a single unit. (3) roll up just the clear 
window of the center section, leaving the screen in place.  
 
Do not use any chemicals or brushes to clean, only mild soap. If the curtains become scratched a 
mild  polishing  compound  (a  white  cream  similar  to  what  is  used  on  Awlgrip)  can  be  applied  by 
hand to remove them.  Test a small, unobtrusive area first. 
 
These curtains are easier to snap on when they expand in the heat than when they shrink in the 
cold.  So,  it’s  best  to  secure  them  when  it’s  still  reasonably  warm.  Always  store  curtains  rolled 
(usually several together and not folded) in a dry place to prevent creasing or shrinking.  

 

 
 
 
 
 

Summary of Contents for 36z Downeast

























































Reviews: