MJ LED LIGHTNING MJ-1350, User Manual

Page: 4 / 12

BEAM SPOT WASH (3IN1) 350W BEAM SPOT WASH (3IN1) 350W
SAFE USAGE OF THE PRODUCT
When unpacking and before disposing of the carton, check there is no transportation
damage before using the product. Should there be any damage caused by
transportation, consult your dealer and do not use the apparatus.
The product is for indoor use only, IP20. Use only in dry locations. Keep this device
away from rain and moisture, excessive heat, humidity and dust. Do not allow contact
with water or any other liquids.
The product is not designed or intended to be mounted directly on to inflammable
surfaces
The product is only intended for installation, operation and maintenance by
professional person.
The product must be installed in a location with adequate ventilation, at least 50cm
from adjacent wall surfaces. Be sure that no ventilation slots are blocked.
Do not product the beam onto inflammable surfaces, minimum distance is 12m.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the
power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation
conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never
let the power-cord come into contact with other cables. Only handle the power-cord
by the plug. Never pull out the plug by tugging the power-cord.
Keep the light clean. Do not touch the light glasss with bare hands.
The product should always be installed with a secondary safety fixing. On the
projector base brink, there is a hole for the safety cord provided. It should be attached
as shown in “installing the projector” section.
The lamp used in this projector is a discharge lamp. After switching off don
,
t attempt
to restart the projector until lamp has cooled, this will require approx 15 minutes.
Switching the lamp on and off at short intervals will reduce the life of both the lamp
and the projector. But occasional breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
The light shall be changed if it has become damaged or thermally deformed or
reached its life limit.
Shields and lens shall be changed if they have become visibly damaged to such an
extent than their effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 70
°。，
when steady state is achieved 140
°。
There is no user serviceable parts inside the projector, do not open the housing and
never operate the product with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
★
Always disconnect from the mains, when the device is not in use or
before cleaning it or before attempting any maintenance work !
1
CH8
144-151
152-159
160-167
168-175
176-183
184-191
192-199
200-228
229-255
Gobo6
Gobo7
Gobo8
Gobo9
Gobo10
Gobo11
Gobo12
Rotating Gobo-Wheel Forwards, Fast-Slow
Rotating Gobo-Wheel Forwards, Slow- Fast
CH9
0-255
Rotation gobo wheel adjusting
Adjusting angle and rotate
CH10 000-019
020-255
Prism
12 Prism indexing
No function
CH11
0-255
Prism rotation fine
Adjusting angle low
CH12
0-255
Frost
Frost function
CH13
Zoom
Zoom from 2.5-40degree
CH14
0-255
Focus
Focus function
CH15
000-031
032-063
064-095
096-127
128-143
144-159
160-191
192-223
224-255
Strobe
Strobe Off
Strobe On
Strobe, Slow-Fast
Strobe On
Slow Close/Fast Open, Fast-Slow
Fast Open/Slow Close, Slow-Fast
Strobe On
Random Strobe, Slow-Fast
Strobe On
CH16
0-255
General dimmer
Linear dimmer, 0-100%
18