Mizuhosi 6875 Preventive Maintenance Download Page 3

  

 

 

6875 hana Table 

                  T e c h n i c a l    S e r v i c e s    D e p a r t m e n t 

Preventative Maintenance Checklist                                             Phone: 800-777-4674 PST     Fax: 510-429-8324 

 
 

50603-06 Rev. A                                                  ECN# 10016                              Effective Date 3/9/2010                                               Page 3 of 4

 

3.3 (   ) (   ) Attach Right & Left Femur Lift assemblies, and connect their electrical cords. 

(Confirm green “LEFT LIFT CONNECTED” and “RIGHT LIFT CONNECTED” lights are on) 

 Comments:__________________________________________________________________________ 
 
3.4 (   ) (   ) Attach Right Leg Spar & Left Leg Spar. 

a. Verify locking knob locks the spar to the table with ease. 
b. Verify Traction unit slides smoothly onto the rail and locking knob locks & unlocks the Traction unit. 
c. Verify Rotational Lock knob is operational and its free of any cracks and/or any other abnormality. 
d. Verify the spar brake lock handle is operational and the spar does not drift down when locked. 
e. Verify Fine Traction when crank has a little bit of tension (If it’s too smooth, please note or call 
Technical Services).    

Comments: _________________________________________________________________________ 

 

4. Control Panel check. 

4.1 (   ) (   ) Power Status Lights; observe the table Power Status lights located on the Control Panel. Confirm green  

“AC Power” light is on. If red “Battery Check” light is on, charge battery for a minimum of 3 hours 
(leave Power Cord plugged in and main “ON/OFF” Power Switch “ON”). 

a. 

Press and hold "HEIGHT UP" / “HEIGHT DOWN" button (run to its limit). 

b.

 Press and hold "REV. TREN"/ "TREN" button (run to its limit). 

c.

 Press and hold "LEFT LATERAL “/ “RIGHT LATERAL ROLL” button (run to its limit). 

d

. “RETURN TO LEVEL (run table to max height up, rev tren, and lateral roll right. Press and hold 

Return to Level button, verify table goes back to level (-+2deg) and to the lowest position. 

e.

 Switch the selector knob to “Left Femur Lift”, press “UP”/”DOWN” on the foot pedal. Confirm 

Femur Lift goes up/down to its limit. 

f.

 Switch the selector knob to “Right Femur Lift”, press “UP”/”DOWN” on the foot pedal. Confirm 

Femur Lift goes up/down to its limit. 

g.

 Press “Emergency Button”. Confirm all indicators for “AC POWER”, “BATTERY OK”, 

“BATTERY POWER”, and “BATTERY CHARGE” will not illuminate except for indicators, “Foot 
Pedal Connected, “Left” / “Right” Lift Connected, and “Left / Right” Femur lift selector.  

Comments: _________________________________________________________________________ 

 

 

5. Hand Pendant check

.  

5.1 (   ) (   ) Confirm green “AC Power” light is on and green “Battery Status” light is on. 

 

 

(

Repeat steps 4.1, a to d

 Comments: 

_________________________________________________________________________ 

 

6. Battery Power Check (disconnect power cord from AC source. Main power switch indicator will dim). 

6.1 (   ) (   ) Confirm the green, “Battery OK” lights is ON at the Control Panel and Hand Pendant are illuminated. If  

not, refer to the Battery System section of the service manual.  

(

Repeat steps 4.1, a to g for this section) 

 

Comments: _________________________________________________________________________ 

 

 
 

Summary of Contents for 6875

Page 1: ...presenting Pass Fail criteria is inspected If a step has failed please indicate with an x and note the reasons in the comments section If you resolve the failure place an x in the Pass area and indicate the corrective action again in the comments section If you are unable to perform any Pass Fail check please contact Mizuhosi Technical Services for assistance and circle the check Biohazards when s...

Page 2: ...__________________________________ 2 3 ON OFF Power Switch Circuit Breaker is properly secured operational and plastic cover is not torn or pierced Comments _________________________________________________________________________ 3 Basic Setup 3 1 Attach Hand Pendant Comments _________________________________________________________________________ 3 2 Power Switch ON a Connect table Power Cord t...

Page 3: ...h ON a Press and hold HEIGHT UP HEIGHT DOWN button run to its limit b Press and hold REV TREN TREN button run to its limit c Press and hold LEFT LATERAL RIGHT LATERAL ROLL button run to its limit d RETURN TO LEVEL run table to max height up rev tren and lateral roll right Press and hold Return to Level button verify table goes back to level 2deg and to the lowest position e Switch the selector kno...

Page 4: ...Covers Using Hand Pendant press and hold HEIGHT UP button raising tabletop to maximum height and toggle Power Switch to OFF 7 1 Visually inspect all stainless steel sheet metal covers for damage verify that they are not bent Comments _________________________________________________________________________ This section is for Technical Services use only Reviewed _________________________ Signature...

Reviews: