background image

A-1

SAFETY PRECAUTIONS

(Read these precautions before use.)

Before using this product, please read this manual and the relevant manuals 
introduced in this manual carefully and pay full attention to safety to handle the 
product correctly.
The instructions given in this manual are concerned with this product. For the 
safety instructions of the programmable controller system, please read the User’s 
Manual for the CPU module.
In this section, the safety precautions are ranked as "DANGER" and "CAUTION".

Note that the 

CAUTION level may lead to a serious consequence according 

to the circumstances.
Always follow the precautions of both levels because they are important to 
personal safety.

Please keep this manual accessible when required and always forward it to the 
end user.

[DESIGN PRECAUTIONS]

DANGER

Do not write data into the "system area" of the buffer memory of intelligent 
function modules. Also, do not use any "prohibited to use" signals as an 
output signal to an intelligent function module from the  programmable 
controller CPU. 
Writing data into the "system area" or outputting a signal for "prohibited to 
use" may cause a programmable controller system malfunction.

DANGER

Indicates that incorrect handling may cause 
hazardous conditions, resulting in death or severe 
injury.

Indicates that incorrect handling may cause 
hazardous conditions, resulting in medium or slight 
personal injury or physical damage.

CAUTION

Summary of Contents for Q68TD-G-H01





















Reviews: