29
E9
Indoor/outdoor unit communication error
(Transmitting error) (Outdoor unit)
1
Abnormal if “0” receiving is detected
30 times continuously though outdoor
controller circuit board has transmitted “1”.
2
Abnormal if outdoor controller
circuit board could not find blank of
transmission path for 3 minutes.
1
Indoor/ outdoor unit connecting
wire has contact failure.
2
Defective communication circuit
of outdoor controller circuit board
3
Noise has entered power supply.
4
Noise has entered indoor/
outdoor unit connecting wire.
1
Check disconnection or looseness of indoor/
outdoor unit connecting wire.
2
~
4
Turn the power off, and on again to
check. Replace outdoor controller circuit
board if abnormality is displayed again.
EF
Non defined error code
This code is displayed when non defined
error code is received.
1
Noise has entered transmission
wire of remote controller.
2
Noise has entered indoor/
outdoor unit connecting wire.
3
Outdoor unit is not inverter
models.
4
Model name of remote
controller is PAR-S25A.
12
Turn the power off, and on again to check.
Replace indoor controller board or outdoor
controller circuit board if abnormality is
displayed again.
3
Replace outdoor unit with inverter type
outdoor unit.
4
Replace remote controller with MA remote
controller.
E8
Indoor/outdoor unit communication error
(Signal receiving error) (Outdoor unit)
Abnormal if outdoor controller circuit board
could not receive anything normally for 3
minutes.
1
Contact failure of indoor/
outdoor unit connecting wire
2
Defective communication circuit
of outdoor controller circuit board
3
Defective communication circuit
of indoor controller board
4
Noise has entered into indoor/
outdoor unit connecting wire.
1
Check disconnection or looseness of indoor/
outdoor unit connecting wire of indoor or
outdoor units.
2
~
4
Turn the power off, and on again to
check. Replace indoor controller board
or outdoor controller circuit board if
abnormality is displayed again.
E3
or
E5
Remote controller transmission error (E3)/
signal receiving error (E5)
1
Abnormal if remote controller could not
find blank of transmission path for 6
seconds and could not transmit.
(Error code: E3)
2
Remote controller receives transmitted
data at the same time, compares the
data, and when detecting it, judges
different data to be abnormal 30
continuous times. (Error code: E3)
1
Abnormal if indoor controller board could
not find blank of transmission path.
(Error code: E5)
2
Indoor controller board receives
transmitted data at the same time,
compares the data, and when detecting
it, judges different data to be abnormal
30 continuous times. (Error code: E5)
1
Set a remote controller to main, and the
other to sub.
2
Remote controller is connected with only one
indoor unit.
3
The address changes to a separate setting.
4
~
6
Diagnose remote controller.
a) When “RC OK” is displayed, remote
controllers have no problem.
Turn the power off, and on again to check.
When becoming abnormal again, replace
indoor controller board.
b) When “RC NG” is displayed, replace
remote controller.
c) When “RC E3” or “ERC 00-66” is
displayed, noise may be causing
abnormality.
1
2 remote controller are set as
“main.”
(In case of 2 remote controllers)
2
Remote controller is connected
with 2 indoor units or more.
3
Repetition of refrigerant
address
4
Defective transmitting receiving
circuit of remote controller
5
Defective transmitting receiving
circuit of indoor controller board
6
Noise has entered into
transmission wire of remote
controller.
* Check LED display on the outdoor controller
circuit board. (Connect A-control service tool,
PAC-SK52ST.)
1
Check disconnection or looseness of
Interface unit/Flow temp. controller or
outdoor unit connecting wire of Interface
unit/Flow temp. controller or outdoor unit.
2
~
4
Turn the power off, and on again to check.
If abnormality generates again, replace
Interface unit/Flow temp. controller or
outdoor controller circuit board.
Interface unit/Flow temp. controller
or outdoor unit communication error
(Signal receiving error)
1
Abnormal if Interface unit/Flow temp.
controller cannot receive any signal
normally for 6 minutes after turning the
power on.
2
Abnormal if Interface unit/Flow temp.
controller cannot receive any signal
normally for 3 minutes.
1
Contact failure, short circuit
or, miswiring (converse wiring)
of Interface unit/Flow temp.
controller or outdoor unit
connecting wire
2
Defective transmitting receiving
circuit of outdoor controller
circuit board
3
Defective transmitting receiving
circuit of Interface unit/Flow
temp. controller
4
Noise has entered into Interface
unit/Flow temp. controller or
outdoor unit connecting wire.
E6
Error Code
Abnormal point and detection method
Judgment and action
Case
Ed
Serial communication error
1
Abnormal if serial communication between
outdoor controller circuit board and
outdoor power circuit board is defective.
1
Breaking of wire or contact
failure of connector CN2
between the outdoor controller
circuit board and the outdoor
power circuit board
2
Breaking of wire or contact
failure of connector CN4
between the outdoor controller
circuit board and the outdoor
power circuit board
3
Defective communication circuit
of outdoor power circuit board
4
Defective communication circuit
of outdoor controller circuit board
for outdoor power circuit board
12
Check connection of each connector CN2
and CN4 between the outdoor controller
circuit board and the outdoor power circuit
board.
3
Replace outdoor power circuit board.
4
Replace outdoor controller circuit board.
OCH533A
