manualshive.com logo in svg

Mitsubishi CNC Meldas HC Series, Specification Manual

Share
Download
Mitsubishi CNC Meldas HC Series Specification Manual Download Page 3

ii

For Safe Use

1. Electric shock prevention

 

DANGER

Wait at least 10 minutes after turning the power OFF, confirm that the servo amplifier CHARGE
lamp has gone out, and check the voltage between P and N terminals with a tester, etc., before
starting wiring or inspections.
Failure to observe this could lead to electric shocks.

Ground the servomotor with Class 3 grounding or higher.

Wiring and inspection work must be done by a qualified technician.

Wire the and servomotor after installation. Failure to observe this could lead to electric shocks.

Do not touch the switches with wet hands. Failure to observe this could lead to electric shocks.

Do not damage, apply forcible stress, place heavy items or engage the cable. Failure to observe

this could lead to electric shocks.

2. Fire prevention

 

CAUTION

Install the servomotor on noncombustible material. Direct installation on combustible material or

near combustible materials could lead to fires.

3. Injury prevention

 

CAUTION

Do not apply a voltage other than that specified in Specification Manual on each terminal. Failure

to observe this item could lead to ruptures or damage, etc.

Do not mistake the terminal connections. Failure to observe this item could lead to ruptures or

damage, etc.

Do not touch the servomotor, while the power is turned ON or immediately after turning the power

OFF. Some parts are heated to high temperatures, and touching these could lead to burns.

Summary of Contents for CNC Meldas HC Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands