-
5
-
WIRELESS REMOTE CONTROLLER • All displays are described in the liquid crystal display for explanation
NAMES AND FUNCTIONS OF REMOTE CONTROLLER BUTTON
OPERATION MODE display
Indicates selected operation with .
FAN SPEED button
Every time this button is pressed, the mode is switched
as below.
HI MED LO
ROOM TEMP display
Indicates set temperature.
FILTER display
Indicates for two seconds when FILTER
button is pressed.
OPERATION MODE select button
Every time this button is pressed, displays switch as below
(AUTO) (COOL) (HEAT)
(FAN) (DRY)
ROOM TEMP/TIME SETTING button
Sets room temperature by pressing or button.
Sets time when setting the time.
ACL switch
Used to reset the microcomputer.
FAN SPEED display
Indicates the selected air flow volume.
FILTER button
ON/OFF button
When this is pressed once, the AIR CON starts to
operate and when this is pressed once again, it stops
operating.
TIMER CANCEL button
Used to cancel the TIMER SETTINGS.
Transmitter
Sends signal to the air conditioner.
Used to reset (turn off) the filter sign.
Press the button only after completing the filter cleaning.
Oper
ation section
Displa
y
section
7
7
7
7
6
8
7
7
8
If the display of remote controller has troubles, press
ACL
switch.
NOTICE
WIRELESS REMOTE CONTROLLER HANDLING PROCEDURE
REPLACING THE BATTERIES
If the following occurs, the batteries are exhausted. Replace with new ones.
•
When the signal is transmitted, the receiver does not display reception.
•
The display fades away or does not show anything.
1
Pull out the cover.
2
Replace the old
batteries with
new ones.
(R03×2
)
3
Close cover.
4
Adjust the current time.
See page 6
W h e n a ny e rro r o c cur s o n t h e
display,
Press
ACL
switch
with
a
ballpoint
etc.
NOTICE
If the remote controller is set as “Radio
Inter feren c e Prevent ion Set t ing ”, it
returns to default when the batteries are
removed. It is necessary to perform the
next procedures again.
Pay attention
to the and
marks
H ow to s et R adio I nte r fe r e nc e
Prevention Setting
It is possible to sent two way. Press
ACL
switch with
AIR FLOW
button
kept pressing or Insert the batterles
w i t h
AIR FLOW
b u t t o n k e p t
pressing.
ATTENTION
• Do not use old and new batteries
mixed.
• R e m ove t h e b a t t e r i e s w h e n t h e
remote controller is not used for a
long time.
• The recommendable effective period
of a battery is about 6 to 12 months.
(It depends on the usage.)
• T h e r e c o m m e n d a b l e e f f e c t i v e
period is printed on the bat ter y.
T h i s m a y b e s h o r t e r d u e t o
manufacturing time of the unit.
• However the batter y may be still
working in order after expiry date.
When the bat teries are inser ted, eac h o peration
mode is set as the right fi gure. Adjust the current time
referring to page 6. (The fi gure is while operation, and
only the current time is displayed while stopping)
SETTING CHANGE OF AUTO MODE OPERATION
Auto mode operation of the KX (except KXR) cannot
be selected. For these models, set the remote
controller to disable the auto mode operation.
While pressing the
MODE
button and then press
the
ACL
switch, or while pressing the
MODE
button and then insert the batteries to the remote
controller, then the auto mode is invalid.
ATTENTION
When the batteries are removed, the system is
returned to initial setting (auto mode is valid). In
case that removing the batteries in the remote
controller, perform the above operation once again.
HOW TO OPERATE
When you press each button of wireless remote
controller, directing properly to the receiver, the signal
is transmitted. If the air conditioner receives the signal
correctly, the light of operation indicator will fl ash.
ATTENTION
The operation of remote controller must
be performed slowly and steadily.
ABOUT REMOTE CONTROLLER HOLDER
The remote controller can be mounted on the wall
or pillar with the remote controller holder.
Slide from the upper part of the holder to place or
take out the remote controller.
ATTENTION
Do not place the remote controller to
the following places.
• The place exposed to direct sunlight or other
strong lighting.
• The place exposed to high temperature, for
EXAMPLE, on the electric carpet or near a stove.
If the receiver is exposed to direct sunlight or
other strong lighting, it may not receive the signal.
In this case, shut out the sunlight or turn down the
lighting.
Do not place anything between the remote
controller and the unit.
Do not operate the remote controller for other
electric appliances which can be operated with
a remote controller.
Handle it with utmost attention.
Even if the remote controller is not found or
damaged, you can operate the air conditioner with
itself. See “Backup button” on page 4.
PJZ012A055̲body̲1221.indd 5
PJZ012A055̲body̲1221.indd 5
2007/12/25 17:59:08
2007/12/25 17:59:08