Mitsubishi Heavy Industries FDCA Series Technical Manual Download Page 148

Page: 148 / 163

146

Error display

[Communications error during operation]

Indoor unit

Red LED

Green LED

2 time flash

Keeps flashing

Red LED

Green LED

2 time flash

Keeps flashing

Outdoor unit

Is the connection

of the signal wires at the

outdoor unit poor?

Is the connection

of the signal wires at the

indoor unit poor?

Did the remote

controller’s LCD return

to normal?

“ WAIT ”

The unit is normal.

Malfunction was due to
transient noise, etc.

Go to display diagnosis (page 136).

YES

(1)

(2)

Repair

Reset power

supply.

YES

“ WAIT ”

Notes (1) Check for poor connections (disconnection, looseness) on the outdoor unit’s terminal block.

(2) Check for poor connections or disconnection of the signal lines between the indoor and outdoor units.

Reset power supply.

Did it return to normal?

YES

Outdoor unit’s control PCB is
faulty. (Network communications
circuit is faulty.) Replace

Malfunction is due to noise, etc.

(The outdoor unit’s CPU went
out of control due to noise during
power on.)

Indoor unit

Red LED

Green LED

2 time flash

Keeps flashing

Red LED

Green LED

Stays OFF

Keeps flashing

Outdoor unit

Error display

e32

[Power supply phases reversed]

Indoor unit

Red LED

Green LED

Stays OFF

Keeps flashing

Red LED

Green LED

1 time flash

Keeps flashing

Outdoor unit

Are the power supply

phases reversed?

YES

Are the connections

to the reverse phase detection

circuit lines correct?

YES

Outdoor unit’s control PCB is faulty.

Replace

(Reverse phase detection circuit is faulty.)

Repair

Summary of Contents for FDCA Series




































































































































































Search results

Summary of Contents for FDCA Series

Reviews:

Mitsubishi Heavy Industries FDCA Series, Technical Manual, Page: 148 / 163

Search results

Summary of Contents for FDCA Series

Reviews: