Mitsubishi Electric PUZ-M200YKA2 Service Manual Download Page 42

Page: 42 / 114

OCH775

How long is “Please Wait”

kept being displayed on the

remote controller?

6 minutes

or more

2 minutes

or less

2 to 6

minutes

YES

Are any check codes

displayed on the

remote controller?

Are any check codes

displayed on the LED?

Symptoms: “Please Wait” is kept being displayed on the remote controller.

Check the display time of “Please Wait”

after turning on the main power.

• “Please Wait”

will be displayed

during the startup

diagnosis after turning

on the main power.

• Normal

The startup diagnosis will

be over in around 2 minutes.

• Miswiring of indoor/

outdoor connecting

wire

• Breaking of indoor/

outdoor connecting

wire (S3)

• Defective indoor

controller board

• Defective outdoor

controller circuit

board

• Refer to “Self-diagnosis

action table” in order to

solve the trouble.

• In the case of

communication errors,

the display of remote

controller may not

match the LED display of

the outdoor unit.

• Defective indoor

controller board

• Defective remote

controller

Check the LED display of the
outdoor controller circuit board.

Diagnosis flow

Cause

Inspection method and

troubleshooting

Summary of Contents for PUZ-M200YKA2



















































































































Search results

Summary of Contents for PUZ-M200YKA2

Reviews:

Related manuals for PUZ-M200YKA2

Brands by name

Popular brands

Mitsubishi Electric PUZ-M200YKA2, Service Manual

Search results

Summary of Contents for PUZ-M200YKA2

Reviews:

Related manuals for PUZ-M200YKA2

Brands by name

Popular brands